This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Parametric Modeling Techniques in Industrial Conceptual Transport Aircraft Design
Technical Paper
2003-01-3052
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
A series of prediction algorithms suitable for the pre-design stage of industrial conceptual transport aircraft design are derived in this treatise. The methods have been devised by hybridizing statistical correlation of design variables, synthetic functions and macro-objective functions with fractional change analytical constructs. Applicability of these prediction algorithms encompasses personal/micro turbofans, business aircraft from very light to ultra-long range categories to commercial aircraft from commuters to narrow-body transports of around 100 PAX. It is highlighted that the methods have been generated from a dataset of information limited to in-production or formally launched transport aircraft, hence reflects only a contemporary level of technological sophistication.
Topic
Citation
Isikveren, A., "Parametric Modeling Techniques in Industrial Conceptual Transport Aircraft Design," SAE Technical Paper 2003-01-3052, 2003, https://doi.org/10.4271/2003-01-3052.Also In
References
- Torenbeek, E. “Synthesis of Subsonic Airplane Design” Delft University Press the Netherlands 1982
- Obert. E. “Some Aspects of Aircraft Design and Aircraft Operation” Linkoping Institute of Technology (LiTH), Aircraft Design Lecture Series Sweden 1996
- Raymer, D.P. “Aircraft Design: A Conceptual Approach” AIAA 1989
- Roskam, J. “Airplane Design” Roskam Aviation and Engineering Corporation Kansas 1990
- Isikveren, AT. “Quasi-analytical Modeling and Optimization Techniques for Transport Aircraft Design” Report 2002-13, Ph.D. Thesis Royal Institute of Technology (KTH), Department of Aeronautics Sweden 2002
- Saeedipour, H.R. Stevenson, T.N. “The Effects of Small Changes to the Design Specification of a Jet Civil Transport Aircraft” Aircraft Design 1 1998 25 41
- Clancy, L.J. “Aerodynamics” Longman Scientific and Technical 1975
- “Geometrical Properties of Cranked and Straight Tapered Wing Planforms” Engineering Science Data Units (ESDU), 76003 January 1976
- Young, A.D. “The Aerodynamic Characteristics of Flaps” Aeronautical Research Council Reports and Memoranda, Ministry of Supply United Kingdom 1953
- Eckert, E.R.G. “Engineering Relations for Friction and Heat Transfer to Surfaces in High Velocity Flow” Journal of the Aeronautical Sciences Vol. 22 1955 585 587
- Boppe, C.W. “CFD Drag Predictions for Aerodynamic Design” AGARD Report AR-256 1989
- Torenbeek, E. “Optimum Wing Area, Aspect Ratio and Cruise Altitude for Long Range Transport Aircraft” Report LR-775 Delft University of Technology, Faculty of Aerospace Engineering The Netherlands October 1994
- “Jet Transport Performance Methods” Seventh Edition Boeing Flight Operations, Boeing Commercial Airplanes May 1989
- Torenbeek, E. Wittenberg, H. “Generalized Maximum Specific Range Performance” Journal of Aircraft Vol. 20 Number 7 July 1983
- Torenbeek, E. “Optimum Cruise Performance of Subsonic Transport Aircraft” Report LR-787 Delft University of Technology, Faculty of Aerospace Engineering the Netherlands March 1995
- GASP - General Aviation Synthesis Program” NASA CR 152303 January 1978
- McCormick, B.W. “Aerodynamics, Aeronautics, and Flight Mechanics” John Wiley and Sons 1979
- Erzberger, H. Lee H. “Characteristics of Constrained Optimum Trajectories with Specified Range” NASA Technical Memorandum 78519 Ames Research Center
- “Definitions and Inputs for Range and Direct Operating Cost Calculation” Appendix 1, G(T) 5656 Association of European Airlines 1990
- “American Airlines Flight Planning System User's Manual” American Airlines Flight Operations Engineering — En route Performance Engineering August 1998
- “Federal Aviation Regulations (FAR), Part 25 Airworthiness Standards: Transport Category Airplanes” US Department of Transportation
- Hale, F.J. “Best-Range Flight Conditions for Cruise-Climb Flight of a Jet Aircraft” NASA Conference Proceedings No. 2001 Vol. 4 1976 1713 1719
- “Citation CJ2 Flight Planning Guide” June 2002
- “Citation CJ3 Preliminary Flight Planning Guide” August 2002
- “Global Express Dimensional Data” MAA700-100 Bombardier Inc. September 1996
- “Type Specification for the Global Express Aircraft Model No. BD-700-1A10” RAD-700-100, Issue C Bombardier Inc. July 2000
- “Saab 2000 Aerodynamic Design Data Book — Section 3 Geometry” 73ADS0014 Amendment B5, Saab Aircraft AB March 1994
- “Saab 2000 Performance Engineer's Handbook” 73ADS0394 Saab Aircraft AB Oct. 1996
- “Program Overview: Embraer 170, Embraer 175, Embraer 190, Embraer 195” Airline Marketing, Embraer - Ft. Lauderdale, PRD0201R4 June 2002