This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Fatigue Testing for Spot Welds – Problems, Solutions and New Development
Technical Paper
2003-01-0976
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Engineering design of spot welded components as well as computational analyse of the local stress in the weld zone require relevant fatigue test data. Those test data, however, are dependent on the applied specimens, on the specimen restrain, on the load introduction into the weld zone as well as on the definition of the specimen failure. The discussion of the advantages and drawbacks as well as of the influence of these factors shows that a deliberate selection of specimens is necessary for different test purposes. For the comparability of the test results it is essential in addition to specify comparable test conditions, e. g. specimen fixturing, load introduction and definition of the specimen failure. On account of the variety of variants, a standardization of suitable specimens and respective test conditions hence constitutes an approach to the determination of relevant and comparable test results.
Recommended Content
Book | Dictionary of Mechanical Engineering |
Ground Vehicle Standard | Metallic Shot and Grit Mechanical Testing |
Aerospace Standard | Inspection and Test Quality Systems Requirements for Aviation, Space, and Defense Organizations |
Authors
Citation
Xu, P. and Böllinghaus, T., "Fatigue Testing for Spot Welds – Problems, Solutions and New Development," SAE Technical Paper 2003-01-0976, 2003, https://doi.org/10.4271/2003-01-0976.Also In
References
- Xu, P. Weber, G. Krause, H.-J. Böllinghaus, Th. 2002 Bewertung und Vereinheitlichung gefügter Dünnblechproben für Schwingversuche im Zeitfestigkeitsbereich FAT-Report 169 Frankfurt
- Bergmann, J. W. Heuler, P. 1994 Übertragbarkeit - ein zentrales Problem der Lebensdauervorhersage schwingbelasteter Bauteile Mat.-wiss. u. Werkstofftech 25 3 10 1994
- N. N. 1989 Resistance Welding Manual 4th Resistance Welders Manufacturers' Association (RWMA) Philadelphia, PA (USA) Dec 1989
- Dietrich, K. Sonsino, C. M. 1995 Korrosionsschwingfestigkeit von punktgeschweißten, verzinkten Feinblechen des Fahrzeugbaus DVM-Report, Bauteil 95 „Korrosion an Fahrzeugen” 281 293
- Radaj, D. Zhang, S. 1995 Punktgeschweißte Doppelhutprofil-Probe unter Torsion Materialprüfung 37 1995 11 12
- Hahn, O. Kurzok, R. Rohde, A. 1998 Untersuchungen zur Übertragbarkeit von Kennwerten einer punktgeschweißten Einelementprobe auf Mehrelementprüfkörper und Bauteile FAT-Report 142 1998
- Eureka - BMFT - Research project 03M3021 1994 Neue Stähle mit hoher statischer, dynamischer und Dauerfestigkeit für den Automobilbau Krupp Hoesch Stahl AG Audi AG Bundesanstalt für Materialforschung und -prüfung (BAM) Fraunfofer- Institut für Betriebsfestigkeit (LBF) 1989 - 1994
- Bathke, W. Stahlfeld, G. 2000 Rissentstehung thermometrisch ermitteln Materialprüfung 42 2000 3 67 73
- Xu, P. Lehmkuhl, B. 2002 Temperaturmessung zum Ermitteln der Rissentstehung und des Rissfortschritts an widerstandspunktgeschweißten Verbindungen bei Ermüdungs-versuchen Tagungs-bericht „Werkstoffprüfung 2002” Dez. 5/6 2002 Bad Nauheim