This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Development of a Dynamic Model for Studying the 1st Generation of Common Rail Injectors for HSDI Diesel Engines
Technical Paper
2001-24-0013
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The aim of this work is to investigate Common Rail injector behavior towards multiple injection strategies. A numerical model has been developed to simulate the electro-fluid-mechanic behavior of a Bosch mass production injector (standard injector) and validation against experiments has been performed. In order make the injector performing multiple injections, a deep investigation has been numerically carried out. The numerical study highlighted different area where injector may be improved with particular emphasis on electronic driving circuit. A new driving circuit concept, previously developed, has been successfully simulated showing promising fast-response capability for injector actuation.
Recommended Content
Technical Paper | PRODUCTION PROBLEMS |
Technical Paper | Friction Material; from Prototype to Production |
Technical Paper | Static Mass Balance Studies of the MELiSSA Pilot Plant: Integration of a Higher Plant Chamber |
Authors
Topic
Citation
Bianchi, G., Pelloni, S., Filicori, F., and Milani, M., "Development of a Dynamic Model for Studying the 1st Generation of Common Rail Injectors for HSDI Diesel Engines," SAE Technical Paper 2001-24-0013, 2001, https://doi.org/10.4271/2001-24-0013.Also In
References
- Stumpp, G. Ricco, M. “Common-Rail – An Attractive Fuel Injection System for Passenger Car DI Engines” SAE Paper 960870 1996
- Boehner, W. Hummel, K. ”Common Rail Injection System for Commercial Diesel Vehicles” SAE Paper 970345 1997
- Renner, G. Koyannagi, K. Maly, R.R. ”Effect of Common Rail Injector Design on the Emission Characteristics of Passenger Car DI Engines” Proceedings of “The fourth International Symposium COMODIA 98” 477 482 1998
- Guerrassi, N. Dupraz, P. ”A Common-Rail Injection System For High Speed Direct Injection Engines” SAE 980803 1998
- Funai, K. Yamaguchi T. Itoh, S. “Injection Rate Shaping Technology with Common-Rail Fuel System (ECD-U2)” SAE Paper 960107 1996
- Flaig, U. Polach, W. Ziegler, G. ”Common Rail System (CR-System) for Passenger Car DI Diesel Engines; Experiences with Application for Series Production Projects” SAE Paper 1999-01-0191 1999
- Ficarella, A. Laforgia, D. Landriscina, V. ”Evaluation of Instability Phenomena in a Common Rail Injection System for High Speed Diesel Engines” SAE Paper 1999-01-0192 1999
- Bianchi, G.M. Pelloni, P. Filicori, F. Vannini, G. “Optimization of the Solenoid valve Behavior in Common-Rail Injection Systems” SAE Paper 2000-01-2042 2000
- Von Kuensberg Sarre, C. Kong, Song-Charng Reitz, R.D. “Modeling the Effects of Injector Nozzle Geometry on Diesel Sprays” SAE Paper 1999-01-0912 1999
- Filicori, F. Lo Bianco, C.G. Tonielli, A. ”Modeling and Control Strategies for a Variable Reluctance Direct-Drive Motor” IEEE Transactions on Industrial Electronics 40 No. 1 February 1993
- Imarisio, R. Ricco, M. Rossi Sebastiano, G.M. “Multiple Injection, a cost effective solution for emission reduction of Common Rail DI Diesel Engines” Aachener Kolloquium Fahrzeug-und Motorentechnik 2000
- Nehmer, D. A. Reitz, R. D. “Measurements of the Effects of Injection Rate and Split Injections on Diesel Engine Soot and NOx Emissions” SAE Paper 940668 1994
- Pierpont, D. A. Montgomery, D.T. Reitz, R. D. ”Reducing Particulate and NOx Using Multiple Injections and EGR in a D.I. Diesel Engine” SAE Paper 940897 1994
- Tow, T. Pierpont, D. A. Reitz, R. D. ”Reducing Particulates and NOx Emissions by Using Multiple Injections in a Heavy Duty D.I. Diesel Engine” SAE Paper 940897 1994
- Chan, M. Das, S. Reitz, R. D. ” Modeling Multiple Injection and EGR Effects on Diesel Engine Emissions SAE Paper 972864 1997
- Han, Z. Uludogan, Ali Hampson, G.J Reitz, R. D. ”Mechanism and NOx Emissions Reduction Using Multiple Injection in a Diesel Engine” SAE Paper 960633 1996
- Ganser. M.A. ”Common Rail Injector with Injection Rate Control” SAE Paper 981927 1998
- Digesu, P. Ficarella, A. Laforgia, D. Bruni, G. Ricco, M. ”Diesel Electro-Injector: A Numerical Simulation Code” SAE Paper 940193 1994
- Bianchi, G.M. Pelloni, P. Corcione, F.E. Luppino, F. “Numerical Analysis of Passenger Car HSDI Diesel Engines with 2 nd Generation of Common-Rail Injection Systems: The Effect of the Multiple Injections on Emissions” SAE Paper 2001-01-1068 2001
- Bianchi, G.M. Pelloni, P. Corcione, F.E. Luppino, F. “On the Optimum Combustion Chamber for the 2 nd Generation of Common Rail Injection Systems” SAE 2000-01-1068 2000
- Zhu, Yuhua Reitz, R.D. “Modeling Fuel System Performance and its Effect on Spray Characteristics” SAE Paper 2000-01-1253 2000
- Hiroyasu, H. “The structure of fuel sprays and the combustion processes in diesel engines” 31-1 1998 Fall Technical Conference ASME
- Badami, M. Nuccio, P. Trucco, G. “Influence of Injection Pressure on the Performance of a DI Diesel Engine with a Common Rail Injection System” SAE Paper 1999-01-0193 1999
- Desantes, J.M. Arrègle, J. Rodriguez, P.J. “Computational Model for Simulation of Diesel Injection Systems” SAE Paper 1999-01-0915 1999
- Blevins, J.A. Wagner, D.A. “An Experimental Investigation on Determining Diesel Injector Flow and Transient Characteristics Using High Response Pressure Measurements” SAE Paper 1999-01-0197 1999
- Herrmann, H.O. Körfer, T. “Recent and Future Developments in Diesel Engine Technology” ATA 53 2000
- Kollmann, K. “Development Trends for Diesel-Powered Passenger Cars” ATA 53 2000
- Borghi, M. Milani, M. Piraccini, M. ”Dynamic Analysis of Diesel Engine Common Rail Injection System. Part I: The Injector Dynamics” Accepted for publication and for presentation at the ASME IMECE 2001 ASME International Mechanical Engineering Congress and Exposition November, 11–16 2001 New York, USA