This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Combustion Process Management in Common Rail DI Diesel Engines by Multiple Injection
Technical Paper
2001-24-0007
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The improvements of the solenoid injector and of the Electronic Control Unit of the present Common Rail injection system (C.R.) allow the use of multiple sequential injections. Thanks to this feature this advanced Common Rail system is capable to perform up to five consecutive injections in one engine cycle thus improving control of the combustion process. In particular, in some operating conditions, the activation of a small injection after the main one allows the oxidation of the soot produced in the previous stages of the combustion process, without increasing nitrogen oxide emissions. This paper describes the experimental results obtained with the application of a prototype of this advanced Common Rail system both to a Fiat L4 1.9 JTD 8 valve engine and to a single-cylinder prototype, having the same combustion system and large optical access allowing investigation of the injection and combustion processes. Multidimensional modelling of the combustion process and pollutants formation was also employed to interpret the trends observed in the experiments.
Authors
Topic
Citation
Beatrice, C., Belardini, P., Bertoli, C., Lisbona, M. et al., "Combustion Process Management in Common Rail DI Diesel Engines by Multiple Injection," SAE Technical Paper 2001-24-0007, 2001, https://doi.org/10.4271/2001-24-0007.Also In
References
- Imarisio, R. Rossi, G.M. “Potential of Future Common Rail DI Diesel Engines” Paper 20A2004. Proceedings of International Symposium: The Future of Diesel Engine Technology for Passenger Cars 12–13 Ottobre 2000 Porto Cervo, Italy
- Kollmann, K. “Development Trends for Diesel Powered Passenger Cars” Paper 20A2003. Proceedings of International Symposium: The Future of Diesel Engine Technology for Passenger Cars 12–13 Ottobre 2000
- Imarisio, R Ricco, M Rossi Sebastiano, G. M. “Multiple Injection, a cost effective Solution for Emission Reduction of Common Rail DI Diesel Engines” Proceedings of Aachener Kolloquium October 4–6 2000 Aachen, Germany
- Hummel, K. Krieger, K. Hansen, N. “Evolution of the Bosch Common Rail System for Passenger Cars” Paper 20A2012. Proceedings of International Symposium: The Future of Diesel Engine Technology for Passenger Cars 12–13 Ottobre 2000
- Meissonnier, G. Bazinet, V. “Injection Control in an Advanced Common Rail Injection Systems” Paper 20A2014. Proceedings of International Symposium: The Future of Diesel Engine Technology for Passenger Cars 12–13 Ottobre 2000
- Farrell, P. V. Chang, C. T. Su, T. F. “High Pressure Multiple Injection Spray Characteristics” SAE Paper 960860
- Bakenhus, M. Reitz, R. D. “Two-Color Combustion Visualization of Single and Split Injection in a Single-Cylinder Heavy-Duty D. I. Diesel Engine Using an Endoscope-Based Imaging System” SAE Paper 1999-01-1112
- Schommers, J. Duvinage, F. Stotz, M. Peters, A. Ellwanger, S. Koyanagi, K. Gilden, H. “Potential of Common Rail Injection System for Passenger Car DI Diesel Engine” SAE Paper 2000-01-0944
- Lisbona, M. G. Olmo, L. Rindone, G. “Analysis of the Effect of Combustion Bowl Geometry of a DI Diesel Engine on Efficiency and Emissions” Proceedings of Conference on Thermofluidynamic Processes in Diesel Engines Valencia 2000
- Beatrice, C. Bertoli, C. Del Giacomo, N. Massoli, P. Migliaccio, M.na “Combustion Behavior Analysis in a Transparent Research Engine Equipped with a Common Rail Diesel Injection System” SAE Paper 2000-01-1825
- Beatrice, C. Belardini, P. Bertoli, C. Lisbona, M.G. Migliaccio, M.na “Combustion patterns in common rail d.i. Engines inferred by experiments and C.F.D. computations” Combustion Science and Technology 2001 162 235 261
- Koyanagi, K. Oing, H. Renner, G. Maly, R. “Optimizing common rail-injection by optical diagnostics in a transparent production type diesel engine” SAE Paper 1999-01-3646
- Hasse, C. Barths, H. Peters, N. “Modelling the effect of Split Injections in Diesel Engines using Representative Interactive Flamelets” SAE Paper 1999-01-3547
- Amsden, A.A. “KIVA-3V: A Block structured KIVA program for Engines with Vertical or Canted Valves” LA-13313-MS, Los Alamos 1997
- Han, Z. Reitz, R.D. ”Turbulence Modelling of Internal Combustion Engines using RNG K-e Models” Comb. Sci. Tech 106 267 1995
- Belardini, P. Bertoli, C. Cameretti, M.C. “Numerical analysis of the influence of the jet breakup model formulation on diesel engine combustion computations” Atomization and Sprays Tech. 8 No. 2 123 154 1998
- Reitz, R. D. “Modelling Atomisation Processes in High-Pressure Vaporising Sprays”.” Atomisation and Sprays Tech. 3 309 337 1987
- O’Rourke, P. J. Amsden, A. A. “The Tab Method for Numerical Calculation of Spray Droplet Break-up” SAE Paper 872089
- Bertoli, C. Migliaccio, M.na “A Finite Conductivity model for Diesel Spray Evaporation” International Journal of heat and fluid flow 20 N.5 552 561 1999
- Hiroyasu, H. Nishida, K. “Simplified three Dimensional Modelling of Mixture Formation and Combustion in a D.I. Diesel Engine” SAE Paper 890269
- Hardenberg, H. O. Hase, F. W. “An Empirical Formula for Computing Pressure Rise Delay of a Fuel from its Cetane Number and from Relevant Parameters of D.I. Diesel Engines” SAE Paper 790493
- Bowman, C. T. Kinetics of Pollutant Formation and Destruction in Combustion” Prog. Energy Combust. Sci 1 33 45 1975
- Belardini P. Bertoli C. Beatrice C. D’ Anna A. Del Giacomo N. “Application of a Reduced Kinetic Model for Soot Formation and Burnout in Three-Dimensional Diesel Combustion Computations” Twenty-Sixth International Symposium on Combustion 2517 2524 The Combustion Institute 1996
- Beatrice, C. Bertoli, C. Mincione, G. ”A Common Rail Hydraulic Simulation Code for Injection Characteristics Investigation: Implementation and Preliminary Results” Proceedings 16 th Annual Conference on Liquid Atomization and Spray Systems -ILASS Europe 2000. Paper I.5. Darmstadt 2000
- Kong, S. C. Senecal, P. K. Reitz, R. D. “Developments in spray modeling in diesel and direct-injection gasoline engines” Oil & Gas Science and Technology – Rev. IFP 54 No. 2 197 204 1999