This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Comparison of Heat Release and NOx Formation in a DI Diesel Engine Running on DME and Diesel Fuel
Technical Paper
2001-01-0651
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Event:
SAE 2001 World Congress
Language:
English
Abstract
Although there seems to be a consensus regarding the low emission potential of DME, there are still different opinions about why the low NOx emissions can be obtained without negative effects on thermal efficiency. Possible explanations are:
- The physical properties of DME affecting the spray and the mixture formation
- Different shape and duration of the heat release in combination with reduced heat losses
In this paper an attempt is made to increase the knowledge of DME in relation to diesel fuel with respect to heat release and NOx formation. The emphasis has been to create injection conditions as similar as possible for both fuels. For that purpose the same injection system (CR), injection pressure (270 bar), injection timing and duration have been used for the two fuels. The only differences were the diameters of the nozzle holes, which were chosen to give the same fuel energy supply, and the physical properties of the fuels.
During the experiments, the start of injection was kept constant, and changing the time for the end of injection varied the duration. This was done in order to study the contribution of the total NOx and other emission at full load from the different stages of the combustion. The corresponding heat release rates were used as input to a zero-dimensional multizone combustion model where the local equivalence ratios were adapted so that the calculated NOx emissions corresponded with those measured.
It was found that the general shape of the heat release rates was about the same for the two fuels. Emissions of CO and HC were higher and soot considerably higher with diesel fuel than with DME. Emissions of NOx were about the same, but the relation between the fuels varied with injection duration. The results from the calculations with the multizone combustion model indicate that the average local equivalence ratio was quite high (ϕ>1) and about the same for the two fuels. As the injection pressure used was considerably lower than normal for diesel fuel operation with a CR injection system, it is assumed that the mixing between the diesel fuel and air was worse than in the normal case. This is also manifested in the higher soot emissions. Thus one explanation why DME yields lower NOx emissions, as compared with diesel fuel injected at considerably higher pressures, is that the local equivalence ratio is higher, giving lower local oxygen concentration and NOx formation.
Some differences between the two fuels were observed regarding the fuel injection. The needle opening speed was somewhat slower with DME and the amount of fuel injected at a given duration varied between the fuels. One reason for that was found to be throttling in the needle valve seat in the DME case.
Authors
Topic
Citation
Egnell, R., "Comparison of Heat Release and NOx Formation in a DI Diesel Engine Running on DME and Diesel Fuel," SAE Technical Paper 2001-01-0651, 2001, https://doi.org/10.4271/2001-01-0651.Also In
References
- Daly, J.J. Jr. Kennedy, G.L. Jr. “Dimethyl Ether: A Safety Evaluation” Chemical Times & Trends January 1987
- Hansen, K.F. Nielsen, L. Hansen, J.B. Mikkelsen, S-E. Landälv, H. Ristola, T. Vielwerth, K. “Demonstration of a DME (Dimethyl Ether) Fueled City Bus” SAE Paper 2000-01-2005 2000
- Kozole, K.H. Wallance, J.S. “The use of Dimethyl Ether as a starting aid for methanol-fueled SI Engines at low temperature” SAE Paper 881677 1988
- Karpuck, M.E. Wright, J.D. Dippo, J.L. Jantzen, D.E. “Dimethyl Ether as an Ignition Enhancer for Methanol-Fueled Diesel Engine” SAE Paper 912420 1991
- Murayama, T. Chikahisa, T. Guo, J. “A Study of a Compression Ignition Engine with Converted Dimethyl as an Ignition Improver” SAE Paper 922212 1992
- Sorenson, S.C. “Performance and Emissions of a 0.273 Liter Direct Injection Diesel Engine Fuelled with Neat Dimethyl Ether SAE Paper 950064 1995
- Fleisch, T. McCarthy, C. Basu, A. Udovich, C. Charbonneau, P. Slodowske, W. Mikkelsen, S-E. McCandless, J. “A New Clean Diesel Technology: Demonstration of ULEV Emissions on a Diesel Engine Fueled with Dimethyl Ether SAE Paper 95006 1995
- Ofner, H. Gill, D.W. Krotscheck, C. “Dimethyl Ether as Fuel for CI Engines - A New Technology and Its Environmental Potential” SAE Paper 981158 1998
- Kapus, P. Ofner, H. “Development of a Fuel Injection Equipment and Combustion Systems for DI Diesels Operated on Dimethyl Ether” SAE Paper 950062 1995
- Kajitani, S. Oguma, M. Mori, T. “DME Fuel Blends for Low-emission, Direct-injection Diesel Engines” SAE Paper 2000-01-20004 2000
- Kajitani, S. Chen, Z.L. Konno, M. Rhee, K.T. “Engine Performance and Exhaust Characteristics of Direct-Injection Diesel Engine Operated with DME” SAE Paper 972973 1997
- Konno, M. Katjitani, S. Oguma, M. Toshiyuki, I. Shima, K-I. “NO Emission Characteristics of a CI Engine Fueled with Neat Dimethyl Ether” SAE Paper 1999-01-1116 1999
- Sorenson, S.C. Glensvig, M. Abata, D.L. “Dimethyl Ether in Diesel Fuel Injection Systems” SAE Paper 981159 1998
- Chen, Z. Kajitani, S. Minegisi, K. Oguma, M. “Engine Performance and Exhaust Gas Characteristics of a Compression Ignition Engine Operated with DME Blended Gas Oil” SAE Paper 982538 1998
- Alam, M. Fujita, O. Ito, K. Kajitani, S. Oguma, M. Machida, H. “Performance of NOx Catalyst in a DI Diesel Engine Operated with Neat Dimethyl Ether” SAE Paper 1999-01-3599 1999
- Wakai, K. Nishida, K. Yoshizaki, T. Hiroyasu, H. “Ignition Delays of DME and Diesel Fuel Sprays injected by a D.I. Diesel Injector SAE Paper 1999-01-3600 1999
- McCandless, J.C. Teng, H. Schneyer, J.B. “Development of a Variable-Displacement, Rail-Pressure Supply Pump for Dimethyl Ether” SAE Paper 2000-01-0687 2000
- Ikeda, M. Mikami, M. Kojima, N. “Exhaust Emissions Characteristics of DME/Diesel Fuel Engine” SAE Paper 2000-01-2006 2000
- Egnell, R. “Combustion Diagnostics by Means of Multizone Heat Release Analysis and NO Calculation” SAE Paper 981424 1998
- Egnell. R. “A Simple Approach to Studying the Relation between Fuel Rate, Heat Release Rate and NO Formation in Diesel Engines” SAE Paper 1999-01-3548 1999
- Egnell. R. “The Influence of EGR on Heat Release Rate and NO-formation in a DI Diesel Engine” SAE Paper 2000-01-2935 2000