This content is not included in your SAE MOBILUS subscription, or you are not logged in.
A Premium Heavy Duty Engine Concept for 2005 and Beyond
ISSN: 0148-7191, e-ISSN: 2688-3627
Published March 01, 1999 by SAE International in United States
This content contains downloadable datasetsAnnotation ability available
It is expected that heavy duty engine legislation in Europe will continue to drive down test cycle BSNox emissions to levels of between 2.5 and 3.5 g/kWh by 2005, with a reduction in particulate emissions to between 0.02 and 0.08 g/kWh. It is unlikely that re-optimisation of existing engine combustion systems alone, such as further retardation of the fuel injection timing, will be sufficient to meet the legislated BSNox targets. Other measures, such as cooled EGR or new aftertreatment systems must therefore be considered. Such emissions control strategies may conflict with other market requirements for improved fuel consumption and increased power density.
In this paper, research at Ricardo into the configuration of a premium heavy duty truck engine for the European market for model year 2005 and beyond, is described. A review of the market requirements, projected to 2005 was undertaken in order to define the specification of the concept engine.
Cooled EGR was selected as the primary emissions control strategy. The impact of this strategy on engine rating and fuel consumption was comprehensively reviewed including a study of a wide range of different turbocharger and EGR circuit configurations. A wastegated, single stage turbocharged, turbocompounded engine was selected as the optimal solution. Further calculations were performed to study the potential of future developments in aftertreatment technology. Finally, a concept design of the engine was produced.
CitationMorgan, R., Edwards, S., Nicol, A., Johnstone, I. et al., "A Premium Heavy Duty Engine Concept for 2005 and Beyond," SAE Technical Paper 1999-01-0831, 1999, https://doi.org/10.4271/1999-01-0831.
Data Sets - Support Documents
|Unnamed Dataset 1|
|Unnamed Dataset 2|
- Havenith C. Verbeek R.P. Heaton D.M. van Sloten P. “Development of a Urea De-NOx Catalyst Concept for European Ultra-Low Emission Heavy-Duty Diesel Engines” SAE 952652
- Nylund N.-O. Aakko P. Mikkonen S. Niemi A. “Effects of Physical and Chemical Properties of Diesel Fuel on Nox Emissions of Heavy-Duty Diesel Engines” SAE 972997
- Havenith C. Needham J.R. Nicol A.J. Such C.H. “Low Emission Heavy Duty Diesel Engine for Europe” SAE 932959
- Zelenka P. Aufinger H. Reczek W. Cartellieri W. “Cooled EGR - A key Technology for Future Efficient HD Diesels” SAE 980190
- Zurbig J. Mathes W. Hofmann L. Schoppe D. “NOx Reduction by Using SCR Exhaust Gas After-treatment from Powerplants to Vehicle Diesel Engines” FISITA 1996
- Fanick E.R. Bykowski B.B. “Simultaneous Reduction of Diesel Particulate and Nox Using a Plasma” SAE 942070
- Such C.H. Andersson P.G. Freeman H.D. Needham J.R. “The Development of Technology for Euro 4 Heavy-Duty Engines” 7th Aachen Colloquium on Automobile & Engine Technology 1 1998
- Havenith C. Such C.H. Porter B.C. Nicol A.J. “Demonstration of a Euro 3 Heavy Duty Diesel Engine using Exhaust Gas Recirculation” 18th Vienna Motor Symposium 1997
- Kohketsu S. Mori K. Sakai K. Hakozaki T. “EGR Technologies for a Turbocharged and Intercooled Heavy Duty Diesel Engine” SAE 970340
- “Nox Absorbers for Diesel Applications” Bailey O. ASEC Manufacturing Website
- Kawanami M. Horiuchi M. Leyrer J. Lox E. Psara D. “Advanced Catalyst Studies of Diesel NOx Reduction for On Highway Trucks” SAE 950154
- Bloon R.L. Brunner N.R. Schroeer S.C. “Fibre Wound Diesel Particulate Filer Durability Experience with Metal Based Additives” SAE 970180
- Coldren D.R. Moncelle M.E. “Advanced Technology Fuel Systems for Heavy Duty Diesel Engines” SAE 973182