Try Mobilus Beta
Search tips
 This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Effectiveness of 2D Digital Image Correlation in Capturing the Fracture Behavior of Sheet Metal Alloys

Journal Article
05-16-02-0009
ISSN: 1946-3979, e-ISSN: 1946-3987
DOI: https://doi.org/10.4271/05-16-02-0009
Published December 14, 2022 by SAE International in United States
Effectiveness of 2D Digital Image Correlation in Capturing the Fracture Behavior of Sheet Metal Alloys
Sector:
Citation: Agha, A., "Effectiveness of 2D Digital Image Correlation in Capturing the Fracture Behavior of Sheet Metal Alloys," SAE Int. J. Mater. Manf. 16(2):99-115, 2023, https://doi.org/10.4271/05-16-02-0009.
Language: English

References

  1. Andrade , F.X.C. , Feucht , M. , Haufe , A. , and Neukamm , F. An Incremental Stress State Dependent Damage Model for Ductile Failure Prediction International Journal of Fracture 200 1-2 2016 127 150
  2. Wierzbicki , T. et al. Calibration and Evaluation of Seven Fracture Models International Journal of Mechanical Sciences 47 4-5 2005 719 743
  3. Bai , Y. and Wierzbicki , T. Application of Extended Mohr–Coulomb Criterion to Ductile Fracture International Journal of Fracture 161 1 2009 1 20
  4. Jia , Y. and Bai , Y. Ductile Fracture Prediction for Metal Sheets Using All-Strain-Based Anisotropic eMMC Model International Journal of Mechanical Sciences 115-116 2016 516 531
  5. Hu , T. , Thomas , G. , and Campbell , C. True Fracture Strain Measurement and Derivation for GISSMO Calibration SAE Int. J. Adv. & Curr. Prac. in Mobility 4 4 2022 1394 1402 https://doi.org/10.4271/2022-01-0237
  6. Li , J. et al. A Method of the Direct Measurement of the True Stress–Strain Curve over a Large Strain Range Using Multi-Camera Digital Image Correlation Optics and Lasers in Engineering 107 2018 194 201
  7. Murienne , B.J. and Nguyen , T.D. A Comparison of 2D and 3D Digital Image Correlation for a Membrane under Inflation Opt Lasers Eng 77 2016 92 99
  8. Mohr , D. and Ebnoether , F. Plasticity and Fracture of Martensitic Boron Steel under Plane Stress Conditions International Journal of Solids and Structures 46 20 2009 3535 3547
  9. Roth , C.C. and Mohr , D. Effect of Strain Rate on Ductile Fracture Initiation in Advanced High Strength Steel Sheets: Experiments and Modeling International Journal of Plasticity 56 2014 19 44
  10. Yang , L. , Smith , L. , Gothekar , A. , and Chen , X. 2010
  11. Charoensuk , K. , Panich , S. , and Uthaisangsuk , V. Damage Initiation and Fracture Loci for Advanced High Strength Steel Sheets Taking into Account Anisotropic Behaviour Journal of Materials Processing Technology 248 2017 218 235
  12. Sutton , M.A. et al. The Effect of Out-of-Plane Motion on 2D and 3D Digital Image Correlation Measurements Optics and Lasers in Engineering 46 10 2008 746 757
  13. Pan , B. , Yu , L. , and Wu , D. High-Accuracy 2D Digital Image Correlation Measurements with Bilateral Telecentric Lenses: Error Analysis and Experimental Verification Experimental Mechanics 53 9 2013 1719 1733
  14. Pan , B. , Yu , L. , and Wu , D. High-Accuracy 2D Digital Image Correlation Measurements Using Low-Cost Imaging Lenses: Implementation of a Generalized Compensation Method Measurement Science and Technology 25 2 2014 025001
  15. Bai , P. , Zhu , F. , and He , X. Optical Extensometer and Elimination of the Effect of Out-of-Plane Motions Optics and Lasers in Engineering 65 2015 28 37
  16. Hoult , N.A. et al. Experimental Accuracy of Two Dimensional Strain Measurements Using Digital Image Correlation Engineering Structures 46 2013 718 726
  17. Wittevrongel , L. et al. Evaluation of Methodologies for Compensation of Out of Plane Motions in a 2D Digital Image Correlation Setup Strain 51 5 2015 357 369
  18. Xu , X. et al. High-Accuracy, High-Efficiency Compensation Method in Two-Dimensional Digital Image Correlation Experimental Mechanics 57 6 2017 831 846
  19. Zhao , J. , Sang , Y. , and Duan , F. The State of the Art of Two-Dimensional Digital Image Correlation Computational Method Engineering Reports 1 2 2019 e12038
  20. Hu , J. 2016
  21. Agha , A. and Abu-Farha , F. Numerical Implementation and Validation of a Viscoelastic-Plastic Material Model for Predicting Curing Induced Residual Stresses in Adhesive Bonded Joints Int J Adhes Adhes 118 2022 103195 https://doi.org/10.1016/J.IJADHADH.2022.103195
  22. Esmaeilpour , H. , Kim , H. , Park , T. , Pourboghrat , F. et al. Effect of Hardening Law and Process Parameters on Finite Element Simulation of Single Point Incremental Forming (Spif) of 7075 Aluminum Alloy Sheet Mechanics & Industry 21 3 2020 302 https://doi.org/10.1051/MECA/2020019
  23. Nazzal , M. , Alkhader , M. , Agha , A. , Abu‐Farha , F. et al. Wrinkling Suppression In Thin Membranes Using Designed Geometrical Features 236 19 2022 10163 10174 https://doi.org/10.1177/09544062221101976
  24. Agha , A. and Abu-Farha , F. Experimental Methods to Capture Curing Induced Effects in Adhesive Bonded Joints Int J Adhes Adhes 104 2021 102735 https://doi.org/10.1016/J.IJADHADH.2020.102735
  25. Agha , A. and Abu-Farha , F. Advanced Anti-Buckling Device Coupled with Real-Time Digital Image Correlation for Complex Cyclic Tension-Compression Testing of Lightweight Materials Evaluation of Existing and New Sensor Technologies for Fatigue, Fracture, and Mechanical Testing 40 54 2022 https://doi.org/10.1520/STP163820210045

Cited By