Results
This specification covers procedures for identifying wrought products of titanium and titanium alloys
Test procedures are described for measuring noise at specific receiver locations (passenger and cargo doors, and servicing positions) and for conducting general noise surveys around aircraft. Procedures are also described for measuring noise level at source locations to facilitate the understanding and interpretation of the data. Requirements are identified with respect to instrumentation; acoustic and atmospheric environment; data acquisition, reduction and presentation, and such other information as is needed for reporting the results. This document makes no provision for predicting APU or component noise from basic engine characteristics or design parameters, nor for measuring noise of more than one aircraft operating at the same time. No attempt is made to suggest acceptable levels of noise or suitable subjective criteria for judging acceptability. ICAO Annex 16 Volume I Attachment C provides guidance on recommended maximum noise levels
This specification covers an acrylonitrile-butadiene (NBR) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. For molded rings, compression seals, O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications, use the AMS-P-83461 specification or the MIL-PRF-25732 specification
This document provides general and specific design guidance for the development of software data loading equipment for all types of aircraft. The primary purpose of data load is to upload loadable software parts to airborne computers. A secondary function of data load is downloading data from airborne computers. Software data load functionality generally falls into the following categories: Portable Data Loader (PDL) for loading equipment on the ground or carried onto aircraft to perform onboard loading. Airborne Data Loader (ADL) for installation on aircraft to perform onboard loading. Data Load Function (DLF) is software that performs the data loading. This document defines data loaders designed to load avionics equipment over a high-speed interface using an Ethernet network protocol. This document defines media interfaces and protocol requirements specific to all data load functions, whether portable or airborne. This document also describes the desired capabilities of data loading
This document is intended to supplement the SAE J1939 documents by offering the SAE J1939 information in a form that can be sorted and search for easier use
This document establishes the minimum training and qualification requirements for ground-based aircraft deicing/anti-icing methods and procedures. All guidelines referred to herein are applicable only in conjunction with the applicable documents. Due to aerodynamic and other concerns, the application of deicing/anti-icing fluids shall be carried out in compliance with engine and aircraft manufacturers’ recommendations. The scope of training should be adjusted according to local demands. There are a wide variety of winter seasons and differences of the involvement between deicing operators, and therefore the level and length of training should be adjusted accordingly. However, the minimum level of training shall be covered in all cases. As a rule of thumb, the amount of time spent in practical training should equal or exceed the amount of time spent in classroom training
The devices of this SAE Standard provide the means by which passenger compartment dimensions can be obtained using a deflected seat rather than a free seat contour as a reference for defining seating space. All definitions and dimensions used in conjunction with this document are described in SAE J1100. These devices are intended only to apply to the driver side or center occupant seating spaces and are not to be construed as instruments which measure or indicate occupant capabilities or comfort. This document covers only one H-point machine installed on a seat during each test. Certified H-point templates and machines can be purchased from: SAE International 400 Commonwealth Drive Warrendale, PA 15096-0001 Specific procedures are included in Appendix A for seat measurements in short- and long-coupled vehicles and in Appendix B for measurement of the driver seat cushion angle. Specifications and a calibration inspection procedure for the H-point machine are given in Appendix C
This SAE recommended practice provides procedures and methods for testing service, spring applied parking and combination brake actuators for air disc brake applications. Methods and recommended samples for testing durability, function and environmental performance are listed in 1.1 and 1.2
This document covers the general physical, electrical, functional, testing, and performance requirements for conductive power transfer, primarily for vehicles using a conductive ACD connection capable of transferring DC power. It defines conductive power transfer methods, including the infrastructure electrical contact interface, the vehicle connection interface, the electrical characteristics of the DC supply, and the communication system. It also covers the functional and dimensional requirements for the vehicle connection interface and supply equipment interface. New editions of the documents shall be backwards compatible with the older editions. There are also sub-documents which are identified by a SAE J3105/1, SAE J3105/2, and SAE J3105/3. These will be specific requirements for a specific interface defined in the sub-document. SAE J3105: Main document, including most requirements. ○ SAE J3105/1: Infrastructure-Mounted Cross Rail Connection ○ SAE J3105/2: Vehicle-Mounted
This SAE Standard specifies a method for testing and measuring elastic constants in friction materials by precise ultrasonic velocity measurements. Measurement methods are also described for measurement of the out-of-plane modulus as a function of pre-load as well as the measurement of engineering constants as a function of temperature. Finally, methods are formulated to produce all engineering constants as a function of pre-load and temperature
This SAE Recommended Practice outlines a procedure for selecting the proper specification for carbon steel sheet and strip which are purchased to make an identified part. Specifications considered are: ASTM A109—Steel, Carbon, Cold Rolled Strip. ASTM A569—Steel, Carbon (0.15 maximum percent), Hot Rolled Sheet, Commercial Quality (HRCQ). ASTM A621—Steel, Sheet, Carbon, Hot Rolled, Drawing Quality (HRDQ). ASTM A622—Steel, Sheet, Carbon, Hot Rolled, Drawing Quality, Special Killed (HRDQSK). ASTM A568—Steel, Carbon and High-Strength Low-Alloy Hot Rolled Sheet, and Cold Rolled Sheet, General Requirements. ASTM A366—Steel, Carbon, Cold Rolled Sheet, Commercial Quality (CRCQ). ASTM A619—Steel, Sheet, Carbon, Cold Rolled, Drawing Quality (CRDQ). ASTM A620—Steel, Sheet, Carbon, Cold Rolled, Drawing Quality, Special Killed (CRDQSK). ASTM A749M—Steel, Carbon and High-Strength Low-Alloy, Hot Rolled Strip, General Requirements. ASTM A635—Steel Sheet and Strip, Carbon, Hot Rolled Commercial Quality
xEVs involved in incidents present unique hazards associated with the high voltage system (including the battery system). These hazards can be grouped into three categories: chemical, electrical, and thermal. The potential consequences can vary depending on the size, configuration, and specific battery chemistry. Other incidents may arise from secondary events such as garage fires and floods. These types of incidents are also considered in the recommended practice (RP). This RP aims to describe the potential consequences associated with hazards from xEVs and suggest common procedures to help protect emergency responders, tow and/or recovery, storage, repair, and salvage personnel after an incident has occurred with an electrified vehicle. Industry design standards and tools were studied and where appropriate, suggested for responsible organizations to implement. Lithium ion (Li-ion) batteries used for vehicle propulsion power are the assumed battery system of this RP. This chemistry is
To present methods which, according to the consensus of the aviation propulsion community represented by SAE Committee E-34, allow the continued assessment of load carrying capacity of current chemistry products during periods of limited or nonavailability of previously used standardized methods
The lubricant performance capability for aero propulsion drive systems is derived from the physical properties of the oil and performance attributes associated with the chemical properties of the oil. Physical properties, such as viscosity, pressure-viscosity coefficient and full-film traction coefficient are inherent properties of the lubricating fluid. Chemical attributes are critical for the formation of protective boundary lubricating films on the surfaces to prevent wear and scuffing. These attributes are also associated with surface initiated fatigue (micropitting). To assure performance and to provide required information for engineering design, methodology for at least five oil properties are being studied: (1) pressure-viscosity coefficient, (2) full-film traction coefficient, (3) scuffing resistance, (4) wear resistance, and (5) micropitting propensity. The pressure-viscosity coefficient can be measured either directly by assessing viscosity as a function of pressure using
This SAE Aerospace Recommended Practice (ARP) is intended to evaluate corrosion inhibiting properties of synthetic gas turbine lubricants and gearbox oils
This specification provides requirements and procedures for hydraulic-pressure leak testing of parts
This specification provides requirements and procedures for hydraulic-pressure leak testing of parts. AMS 2625 is the inch/pound version of this MAM
This specification covers established metric manufacturing tolerances applicable to copper and copper alloy sheet, strip, and plate ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted
This specification covers steel cleanliness requirements in metric (SI) units for premium aircraft-quality ferromagnetic steels, other than hardenable, corrosion-resistant steels, by magnetic particle inspection methods
This specification provides requirements and procedures for air-pressure leak testing of parts
This specification covers manufacturing tolerances applicable to seamless and welded tubing of corrosion and heat resistant steel ordered to metric dimension. These tolerances apply to all conditions and are based on individual measurements, unless otherwise noted. Tubing may be specified by two dimensions only (OD and wall thickness, ID and wall thickness, or OD and ID
This specification covers steel cleanliness requirements in metric SI units for special aircraft-quality ferromagnetic steels, other than hardenable corrosion resistant steels, by magnetic particle inspection methods
This specification covers established metric manufacturing tolerances applicable to low-alloy steel bars ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. The term 'exclusive' is used to apply to the higher figure of the specified range
This specification covers procedures for identifying carbon and low-alloy steels, corrosion- and heat-resistant steels and alloys, maraging and other highly alloyed steels, and iron alloy sheet, strip, and plate, and aircraft tubing
This specification covers cotter pins made to metric dimensions from a corrosion and heat resistant steel
This specification covers established metric manufacturing tolerances applicable to aluminum alloy drawn tubing ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" applies only to the higher figure of the specified range
This specification covers established metric manufacturing tolerances applicable to copper and copper alloy seamless tubing ordered to metric (SI) dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "exclusive" is used to apply only to the higher figure of a specified range
This specification covers established metric manufacturing tolerances applicable to bars and rods of copper and copper alloys ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "exclusive" is used to apply only to the higher figure of a specified range
The aviation, space, and defense industries rely on the development and manufacture of complex products comprised of multiple systems, subsystems, and components each designed by individual designers (design activities) at various levels within the supply chain. Each design or manufacturing activity controls various aspects of the configuration and specifications related to the product. When a change to design or process is requested or required, the change is typically required to be evaluated against the impacts to the entire system. Proposed changes to design data/information that the design activity identifies to be minor and have no effect on the product requirements or specifications, have the potential to be implemented and approved, where authorized to do so, but requires notification. Changes that affect customer mandated requirements or specifications shall be approved prior to implementation. In many cases, the design activity is not conducted by the DAH or design authority
AS8049A currently requires adjustable features on aircraft seats to be designed so they can be returned to the positions required for taxi, takeoff and landing by the occupant without the release of the occupant restraints. This ARD will demonstrate Aviation Industry support for revisions to TSO-C39c and TSO-C127a to allow Technical Standard Order (TSO) approval of aircraft seat products designed with adjustable features that require the release of occupant restraints to return the feature to the taxi, takeoff and landing position
This SAE Aerospace Recommended Practice (ARP) addresses the general procedure for the best practices for minimizing uncertainty when calibrating thermal conductivity and cold cathode vacuum gauges, which includes the vacuum sensor(s) and accompanying electronics necessary for a pressure measurement to be made. It also includes the best practices for an in-process verification where limitations make it impossible to follow the best practices for minimizing uncertainty. Verifying the accuracy and operation of vacuum gauges is critical to ensure the maintenance of processes while under vacuum
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate 0.005 to 1.000 inches (0.13 to 25.40 mm) in nominal thickness in the solution heat-treated condition
This specification covers a precipitation hardenable corrosion- and heat-resistant nickel alloy in the form of seamless tubing
This specification covers established metric manufacturing tolerances applicable to low-alloy steel sheet, strip, and plate ordered to metric dimensions. These tolerances apply to all conditions unless otherwise noted. The term 'excl' is used to apply only to the higher figure of the specified range
This specification covers the engineering requirements for electrodeposition of silver on other metals, usually with a nickel strike between the basis metal and the silver, and the properties of the deposit. AMS 2410 is the inch/pound version of this MAM. This processes has been used typically to provide a bearing surface and to prevent galling or seizing of surfaces of parts made of corrosion-resistant steels and alloys and of parts made of other metals not deleteriously affected by high-temperature baking, but usage is not limited to such applications
This specification covers a corrosion and heat resistant steel in the form of welding wire. AMS 5822 is the inch/pound version of this MAM. This product has been used typically as bare filler metal for gas-metal-arc or gas-tungsten-arc welding of steels of similar composition, but usage is not limited to such applications
This specification covers a nickel alloy in the form of wire, rod, strip, foil, and powder and a viscous mixture (paste) of the powder in a suitable binder and procured in metric units. AMS 4778 is the inch/pound version of this MAM. This filler metal has been used typically for joining corrosion and heat resistant steels and alloys requiring corrosion and oxidation resistant joints with good strength at elevated temperatures, but usage is not limited to such applications. Also may be used as a corrosion and oxidation resistant hard coating
This specification covers an aluminum alloy in the form of hand forgings and rolled rings procured to metric (SI) dimensions. These products have been used typically for complex shaped parts requiring moderate strength and good forgeability of the alloy and where stability is required during machining, but usage is not limited to such applications. Corrosion resistance of this alloy is superior to that of aluminum alloys having copper as the principal alloying element
Items per page:
50
1 – 50 of 206833