This specification covers a titanium alloy in the form of bars up through 4.000 inches (101.60 mm) in nominal diameter or least distance between parallel sides, inclusive, forgings of thickness up through 4.000 inches (101.60 mm), inclusive, with bars and forgings having a maximum cross-sectional area of 32 square inches (204.46 cm2), and stock for forging of any size (see 8.6AMS G Titanium and Refractory Metals Committee
This specification covers an aluminum alloy in the form of sheet 0.020 to 0.128 inch (0.51 to 3.25 mm), inclusive, in nominal thickness (see 8.5AMS D Nonferrous Alloys Committee
This specification covers a silicone (MQ/VMQ) elastomer that can be used to manufacture product in the form of sheet, strip, tubing, extrusions, and molded shapes. This specification should not be used for molded rings, compression seals, molded O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applicationsAMS CE Elastomers Committee
This specification covers an aluminum alloy in the form of plate 1.000 to 6.000 inches (25.40 to 152.40 mm), inclusive, in nominal thickness (see 8.5AMS D Nonferrous Alloys Committee
This specification covers an aluminum alloy in the form of sheet and plate 0.017 to 2.000 inches (0.43 to 50.80 mm), inclusive, in nominal thickness (see 8.6AMS D Nonferrous Alloys Committee
This specification covers an aluminum alloy in the form of extruded rods, bars, and profiles (shapes) 0.040 to 1.500 inches (1.02 to 38.10 mm), inclusive, in thickness, and produced with maximum cross-sectional area of 23.25 square inches (15000 mm2) and a maximum circumscribing circle diameter (circle size) of 15.5 inches (394 mm) (see 2.4.1 and 8.6AMS D Nonferrous Alloys Committee
This specification covers an aluminum alloy in the form of alclad coiled sheet from 0.010 to 0.128 inch (0.25 to 3.25 mm), inclusive, in thickness supplied in the -T4 temper (see 8.5AMS D Nonferrous Alloys Committee
This specification establishes requirements for a tape that is used to perform organic coatings adhesion testingAMS G8 Aerospace Organic Coatings Committee
This specification covers a titanium alloy in the form of bars, forgings, and flash-welded rings up through 12.000 inches (304.80 mm), inclusive, in diameter or least distance between parallel sides, and stock of any size for forging or flash-welded rings. Bars, forgings, and flash-welded rings with a nominal thickness of 3.000 inches (79.20 mm) or greater shall have a maximum cross-sectional area of 113 square inches (729 cm2) (see 8.5AMS G Titanium and Refractory Metals Committee
This specification establishes nondestructive testing methods, sampling frequency, and acceptance criteria for the inspection of metal castingsAMS B Finishes Processes and Fluids Committee
This specification covers an aluminum alloy in the form of alclad sheet over 0.039 to 0.126 inches (0.99 to 3.20 mm), inclusive, in nominal thickness with a fine-grain core of ASTM No. 6 or finer (see 8.5AMS D Nonferrous Alloys Committee
This method outlines a standard procedure for performing conformity tests of bearings utilizing liners of bonded polytetrafluoroethylene (PTFE). The data from these tests shall be used to determine if the product meets the conformity requirements of the applicable specificationACBG Plain Bearing Committee
This procurement specification covers the requirements for metal tube support clamps comprising of two spring clips made of corrosion and heat resistant steel and the associated PTFE single split cushion that supports the tube. See Figure 1G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies
This SAE Aerospace Standard (AS) defines minimum performance standards (MPS) for fuel flowmeters, fuel flow indicators, and fuel flow transmitters. The fuel flow indicators and transmitters are intended for use in 14 CFR Part 23, 25, 27, and 29 aircraft equipped with reciprocating and turbine engines. Multiple function displays are not within the scope of this SAE Aerospace Standard (refer to AS6296A-4FLW Fuel Flowmeters
This SAE Standard covers complete general and dimensional specifications for flareless type of hydraulic tube fittings. These fittings are intended for general application in hydraulic systems on industrial equipment and commercial products. These fittings are capable of providing leakproof, full flow connections in hydraulic systems operating at working pressures as specified in Table 1. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and fitting manufacturer to assure that performance levels will be safe and satisfactory. Formerly, SAE J514 was organized as a single document with ten clauses, which included six sections. This revision of SAE J514 has been organized into three sections as follows: Part 1: 37-degree flared fittings Part 2: Flareless (bite type) fittings Part 3: NPTF pipe fittings and pipe unions It is important to note that this and all SAE J-documents are intended for ground vehicle use only and not intendedHydraulic Tube Fittings Committee
This procurement specification covers tubular, blind rivets fabricated from a corrosion resistant nickel-copper alloy of the type identified under the Unified Numbering System as UNS N04405, and of 52 ksi minimum shear strength for self-plugging style rivetsE-25 General Standards for Aerospace and Propulsion Systems
This technical information report (IR) presents a methodology to evaluate battery pack liquid leak tightness attributes to be used in a production line to satisfy the functional requirement for IPX7, water ingress requirement, and no sustainable coolant leakage for coolant circuits. The Equivalent Channel Method is used as a suggested production leak tightness requirement for a given battery pack design that will correlate and assure that the battery pack meets or exceeds its functional requirement. Obtaining the specific geometry of the Equivalent Channel (EC) for a given battery pack is done analytically and empirically in consideration of the product design limitations. This document is a precursor to J3277-1, which will present the practices to qualify that product leak tightness is equal or better than the maximum allowed EC for that product using applicable and commercially available leak test technologies. This document may be applied to EV and HEV battery packs as tested duringBattery Standards Testing Committee
This SAE Aerospace Information Report (AIR) lists military and industry specifications, standards, recommended practices, and information reports applicable to aerospace hydraulic and pneumatic systems and componentsA-6 Aerospace Actuation, Control and Fluid Power Systems
This procurement specification covers solid rivets and hollow end rivets made from a corrosion and heat resistant steel of the type identified under the Unified Numbering System as UNS S66286 and of 80 ksi single shear strength at room temperatureE-25 General Standards for Aerospace and Propulsion Systems
This procurement specification covers aircraft-quality solid rivets made from a corrosion resistant nickel-copper alloy of the type identified under the Unified Numbering System as UNS N04400 and of 46 ksi minimum shear strengthE-25 General Standards for Aerospace and Propulsion Systems
SAE J3078 provides test methods and criteria for the evaluation of the operator enclosure environment in earth-moving machinery as defined in ISO 6165. SAE J3078/1 gives the terms and definitions which are used in other parts of SAE J3078. It is applicable to Off-Road Self-Propelled Work Machines as defined in SAE J1116 and tractors and machinery for agriculture and forestry as defined in ANSI/ASAE S390HFTC6, Operator Accommodation
This specification establishes requirements for a heat resistant aluminized organic coating with sufficient corrosion and erosion resistance for the finished substrateAMS G8 Aerospace Organic Coatings Committee
Specifications, test methods, and usage provisions for safety glazing materials used for glazing of motor vehicles and motor vehicle equipment operating on land highwaysGlazing Materials Standards Committee
This SAE Recommended Practice provides the framework to allow reprogramming software applications from all vehicle manufacturers the flexibility to work with multiple vehicle data link interface tools from multiple tool suppliers. This system enables each vehicle manufacturer to control the programming sequence for electronic control units (ECU’s) in their vehicles, but allows a single set of programming hardware and vehicle interface to be used to program modules for all vehicle manufacturers. This document does not limit the hardware possibilities for the connection between the PC used for the software application and the tool (e.g., RS-232, RS-485, USB, Ethernet…). Tool suppliers are free to choose the hardware interface appropriate for their tool. The goal of this document is to ensure that reprogramming software from any vehicle manufacturer is compatible with hardware supplied by any tool manufacturer. The U.S. Environmental Protection Agency (EPA) and the California AirVehicle E E System Diagnostic Standards Committee
This specification covers nitrile-butadiene elastomer in the form of molded sheet and shapes, color coded yellow per ARP1527AMS CE Elastomers Committee
This report provides current practice measurement methods for quantifying nonvolatile particle matter at the exit plane of aircraft gas turbine engines. This document contains detailed information for many instruments and techniques, described in AIR5892A, that have been applied in aircraft engine field tests since AIR5892A was first issued in April 2003. There are four sections, identified as Technical Appendices (TA), presenting measurement techniques, sampling, and quantification of nonvolatile particles. The sections are written in the format of Aerospace Recommended Practice (ARP) documents and intended to progress to recommended practices upon overcoming existing technical challenges. Many important technical advances have been accomplished that comprise the Aircraft Engine Exhaust Nonvolatile Particle Matter Measurement Method Development techniques described in TA A: Particle Mass,TA B: particle Number and Size,TA C: Particle Sampling, and TA D: Calculation of Particle NumberE-31P Particulate Matter Committee
This SAE Aerospace Information Report (AIR) discusses the sources of Copper in aviation jet fuels, the impact of Copper on thermal stability of jet fuels and the resultant impact on turbine engine performance, and potential methods for measurement and reduction of the catalytic activity of Copper contamination in jet fuels. This document is an information report and does not provide recommendations or stipulate limits for Copper concentrations in jet fuelsAE-5B Aircraft and Engine Fuel and Lubricant Sys Components
The complete requirements for procuring the product shall consist of this document and the latest issue of the basic specification, AMS2431AMS B Finishes Processes and Fluids Committee
The complete requirements for procuring the product shall consist of this document and the latest issue of the basic specification, AMS2431AMS B Finishes Processes and Fluids Committee
This ARP provides recommended use and installation procedures for bonded cable harness supportsAE-8A Elec Wiring and Fiber Optic Interconnect Sys Install
Over the years during which fluid filtration systems have been developing, many terms have come into use for descriptions of characteristics of filter media, filter assemblies, test methods, and test materials. Inevitably, some terms have been applied loosely, so that the same term may have different meaning to different people, or in different frames of reference. Recognizing the need for clearly defined terms, which can have only one meaning for all persons in all circumstances, so that documents dealing with standard methods of evaluation of filters will have only one interpretation, the Filter Test methods Subcommittee of the SAE Engine Committee has compiled this Glossary of related terms. No attempt has been made to produce an all-inclusive document, containing definitions of all terms related to all types of fluid filters. Instead, the Glossary is confined to the terms likely to be encountered in relation to filters for lubricating oil and fuels. At the same time, we haveFilter Test Methods Standards Committee
This ARP outlines recommended practices to quantify the concentrations of a subset of bleed air contaminant marker compounds on an aircraft propulsion engine or APU prior to delivery and installation on civil and military aircraft. Testing is specified during steady state (non-transient) operation only, in a ground level test bed. Included are recommended test setup, test procedures, techniques for sampling ambient air and bleed air, and one or more specific analytical methodologies for each of the suggested bleed air contaminant marker compounds at quantification levels, given practical constraintsE-31B Bleed Air Committee
In accordance with § 4.11 of AS36100, materials used in the construction of pallets, nets, and containers shall take into account the effects of environmental conditions, such as temperature, humidity, and UV degradation, expected in service. In accordance with (E)TSO-C90, the applicant shall consider environmental degradation due to aging, ultra-violet (UV) exposure, weathering, etc., for any materials used in the construction of pallets, nets, and containers. The purpose of this Aerospace Recommended Practice (ARP) is to provide guidelines for the basic requirements to be considered regarding environmental degradation effects when qualifying composite materials in the design to fulfill the (E)TSO-C90 Minimum Performance Standard. Material qualification is the verifying of a materials attributes and characterizations, which are typically determined through testing. Material variances related to raw materials and manufacturing processes are not part of this Aerospace Recommendednull, null
The fluid flow treated in this section is isothermal, subsonic, and incompressible. The effects of heat addition, work on the fluid, variation in sonic velocity, and changes in elevation are neglected. An incompressible fluid is one in which a change in pressure causes no resulting change in fluid density. The assumption that liquids are incompressible introduces no appreciable error in calculations, but the assumption that a gas is incompressible introduces an error of a magnitude that is dependent on the fluid velocity and on the loss coefficient of the particular duct section or piece of equipment. Fig. 1A-1 shows the error in pressure drop resulting from assuming that air is incompressible. With reasonably small loss coefficients and the accuracy that is usually required in most calculations, compressible fluids may be treated as incompressible for velocities less than Mach 0.2. At higher velocities and for large loss coefficients (Kt and 4fL/D), compressible flow analysis shouldAC-9 Aircraft Environmental Systems Committee
This SAE Aerospace Recommended Practice (ARP) details the recommended process for correcting measured non-volatile Particulate Matter (nvPM) mass and number data for particle losses in the sampling and measurement system specified in ARP6320. This technique is only recommended for conditions where both nvPM mass and number concentration measurements are in the valid measurement ranges of the instruments which are discussed in the tool limitations section. This ARP also supplies an Excel® software tool with documentation to automate the process. The body of the ARP details the recommended calculation method, uncertainties and limitations of the system loss correction factors. It explains, in detail, the required inputs and outputs from the supplied Excel® software tool (developed on Windows 7, Excel® 2016). Also included are: The Excel® correction tools (Attachments I and V). Installation instructions for a Windows based computer (Attachment II). A user technical manual (Attachment IIIE-31P Particulate Matter Committee
This Aerospace Information Report (AIR) describes equivalent types of equipment that can perform fire tests in accordance with requirements of AS 1055G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies