AS5970A: FITTING ASSEMBLY, ELBOW, 90°, AXIALLY SWAGED, HYDRAULIC, 5080 PSI

Features

Issuing Committee: G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies

Scope

Content: No Scope available

Rationale

Content

ADDED -20 SIZE AND NOTE 13 AND 14, REVISED NOTE 10 AND WEIGHT HEADER

(SEE TABLE 1A, 1B & 1C FOR DIMENSIONAL INFORMATION)

/1/

MATERIALS:

CODE LETTER "T"

RINGS	-	AMS 4965 TITANIUM ALLOY, 6.0AL 4.0V SOLUTION HEAT TREATED AND AGED OR AMS 4928 TITANIUM ALLOY 6.0 AL 4.0 V ANNEALED WITH HIGH STRENGTH CARBON FIBER/EPOXY RESIN COMPOSITE REINFORCEMENT.
BODY	-	AMS 4928 TITANIUM ALLOY, 6.0AL 4.0V ANNEALED

2
FINISH:

TITANIUM - NONE REQUIRED

/3/

COATINGS/LUBRICANTS:

RINGS	-	THE OUTER SURFACE SHALL HAVE A .125" MINIMUM WIDTH BLUE COLORED RING OR COMPLETELY COLORED BLUE TO INDICATE 5080 PSI MAXIMUM OPERATION PRESSURE. AN AS1241 FLUID RESISTANT PTFE COATING OR PAINT MUST BE USED.
BODY	-	SOLID FILM LUBRICANT PER AS5272, TYPE I OR II, PTFE OR PETROLEUM-BASED LUBRICANT MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID.

/ 4 /
PROCUREMENT SPECIFICATION: PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LISTING FOR PR I-QPL-AS5958 FOR THIS STANDARD. SEE HTTP://WWW.PRI.ORG/QPL/AS5958.PDF FOR CURRENT QPL ONLINE.
5
DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION.
/ 6 /
IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS5958 AND SHALL BE IDENTIFIED ON EITHER RING IN THE AREA SHOWN.
7
FITTINGS SHALL BE INSTALLED IN ACCORDANCE WITH AS5959.
8
SURFACE TEXTURE: SYMBOLS PER AMERICAN SOCIETY OF MECHANICAL ENGINEERS ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED THE MAXIMUM MACHINED SURFACES SHALL BE 125 μin Ra.
9
DIMENSIONS AND TOLERANCES SHALL BE IN ACCORDANCE WITH AMERICAN SOCIETY OF MECHANICAL ENGINEERS, ASME Y14.5M-1994.
1. a
  DIMENSIONS ARE IN INCHES UNLESS OTHERWISE SPECIFIED
2. b
  DIMENSIONAL TOLERANCES SHALL BE +/-.005 INCHES UNLESS OTHERWISE SPECIFIED
3. c
  ANGULAR TOLERANCES SHALL BE +/-0.50 DEGREES UNLESS OTHERWISE SPECIFIED
4. d
  BREAK ALL EDGES .003-.010 INCHES UNLESS OTHERWISE SPECIFIED
10
INTERPRETATION OF DRAWING PER ARP4296
/ 11 /
THIS DIMENSION IS THE ALLOWABLE TUBE END POSITIONING FOR SYSTEM LAYOUT DESIGN.
/ 12 /
.030 MIN RADIUS UNLESS QUALIFICATION OF SPECIAL PROCESS WITH SMALLER RADIUS.
/ 13 /
DIMENSION A AND B IS THE FITTING LENGTH PRIOR TO SWAGE AND A1 AND B1 IS THE FITTING LENGTH AFTER SWAGE.
/ 14 /
THE CHANGE BAR ( | ) LOCATED IN THE LEFT MARGIN IS FOR CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION TO THE DOCUMENT.
/ 15 /
EXAMPLE OF PART NUMBER:

Meta Tags

Topics: Parts
Titanium alloys
Heat treatment
Lubricating greases
Assembling
Coatings, colorants and finishes
Fibers
Composite materials
Fittings

Details

DOI: https://doi.org/10.4271/AS5970A

Pages: 3

Citation: SAE International Technical Standard, FITTING ASSEMBLY, ELBOW, 90°, AXIALLY SWAGED, HYDRAULIC, 5080 PSI, SAE Standard AS5970A, Revised July 2007, Issued January 2006, https://doi.org/10.4271/AS5970A.

Additional Details