This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Chemical Compositions of SAE Alloy Steels
- Ground Vehicle Standard
- J404_200006
- Revised
Sector:
Issuing Committee:
Language:
English
Scope
In 1941, the SAE Iron and Steel Division in collaboration with the American Iron and Steel Institute (AISI) made a major change in the method of expressing composition ranges for the SAE steels. The plan, as now applied, is based in general on narrower ladle analysis ranges plus certain product (check) analysis allowances on individual samples, in place of the fixed ranges and limits without tolerances formerly provided for carbon and other elements in SAE steels (reference SAE J408).
ISTC Divison 1 has developed a procedure which allows for the maintenance of the grade list in this SAE Standard. This will involve conducting an industry-wide survey to solicit input. This survey will be conducted at a frequency deemed necessary by the technical committee. Criteria have been established for the addition to or deletion of grades from the grade table. A new grade will be considered if it meets standard SAE grade ranges, has a minimum usage or production of 225 tonnes/year (250 tons/year), and has the endorsement of at least two users or producers. New steel compositions will still be considered as Potential Standard (PS) steels, based on the guidelines provided in SAE J1081, until such time as production of the new steel achieves a level of production or usage qualifying it for consideration as a standard steel.
The deletion of a grade from the grade table will be by consensus based on the grade survey results. Deleted grades will be archived in SAE J1249 for future reference.
The compositions in this document may apply to open hearth and basic oxygen, or electric furnace steels. Grades shown in Table 1 with prefix letter E are normally made by the electric furnace process with maximum limits of 0.025% phosphorus and 0.025% sulfur. The nominal chemical limits or ranges in the compositions given in Table 1 are subject to standard variations in check analysis given in SAE J409. Since AISI is no longer issuing steel grade designations, all grades listed in this document are SAE grades.
Table 1 is applicable to billets, blooms, slabs, plates, wire rods, and hot-rolled and cold-finished bars.
SAE J404 is not applicable to the following product forms:
-
a
Structural shapes—Not normally furnished to alloy chemistries
-
b
Sheet and strip, hot-rolled and cold-rolled—Refer to ASTM A 506 and A 507
-
c
Seamless and welded mechanical tubing—Refer to ASTM A 513 and A 519
Recommended Content
Ground Vehicle Standard | Chemical Compositions of SAE Alloy Steels |
Technical Paper | Performance of Zinc-Nickel Alloy Electrodeposits as Affected by Internal Stress |
Technical Paper | Automotive Materials-Past, Present and Future |
Data Sets - Support Documents
No Datasets Available
Issuing Committee
Carbon and Alloy Steels Committee
The Carbon and Alloy Steels Committee of MTEC develops and maintains SAE Standards, Recommended Practices and Information Reports relating to Carbon and Alloy Steels. Participants in the Carbon and Alloy Steels Committee include OEMs, suppliers, consulting firms, government and other interested parties.
Reference
Number | Title |
---|---|
ASTMA506 | This document is not part of the subscrption. |
ASTMA507 | This document is not part of the subscrption. |
ASTMA513 | This document is not part of the subscrption. |
ASTMA519 | This document is not part of the subscrption. |
J1081_202306 | Potential Standard Steels |
J1249_202403 | This document is not part of the subscrption. |
J408 | This document is not part of the subscrption. |
J409_202107 | Product Analysis - Permissible Variations from Specified Chemical Analysis of a Heat or Cast of Steel |
* Redlines comparisons are available for those standards
listed in the Revision History that contain a radio button. A
redline comparison of the current version against a revision is
accomplished by selecting the radio button next to the standard and
then selecting 'compare'. At this time, Redline versions only exist
for some AMS standards. SAE will continue to add redline versioning
with ongoing updates to SAE MOBILUS.