This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Defining Hydraulic Oil Compatibility with Hydraulic Hose Elastomers
- Ground Vehicle Standard
- J2631_201110
- Stabilized
Downloadable datasets available
Annotation ability available
Sector:
Issuing Committee:
Language:
English
Scope
This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property—Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.
Rationale
This document has been determined to contain basic and stable technology which is not dynamic in nature.
Recommended Content
Aerospace Material Specification | Aluminum Alloy, Bars, Rolled Or Cold Finished 1.0mg 0.60si 0.28cu 0.20cr Stress Relief Stretched |
Aerospace Standard | STUD - STRAIGHT, DRILLED, .2500-20UNS X .2500-28UNF-3A |
Aerospace Material Specification | Manganese Alloy, Brazing Filler Metal 66Mn - 16Ni - 16Co - 0.80B 1770 to 1875 °F (966 to 1024 °C) Solidus-Liquidus Range |
Topic
Data Sets - Support Documents
Title | Description | Download |
---|---|---|
Unnamed Dataset 1 | ||
Unnamed Dataset 2 | ||
Unnamed Dataset 3 | ||
TABLE 1 | RANGES AND VALUES FOR EACH PROPERTY | |
TABLE 1 | RANGES AND VALUES FOR EACH PROPERTY | |
TABLE 2 | ELASTOMER COMPATIBILITY INDEX DEVELOPMENT | |
TABLE 3 | ELASTOMER COMPATIBILITY INDEX DEVELOPMENT | |
TABLE A1 | SRE-CR/1 | |
TABLE A2 | SRE-NBR/SX | |
TABLE B1 | AGED TEST DATA FROM FACTORY FILL FLUID TYPE CAT 8T-9580 STANDARD NITRILE | |
TABLE B2 | AGED TEST DATA FROM FACTORY FILL FLUID TYPE CAT 8T-9580 STANDARD CHLOROPRENE | |
TABLE B3 | AGED TEST DATA FROM FACTORY FILL FLUID TYPE JDM J21A STANDARD NITRILE | |
TABLE B4 | AGED TEST DATA FROM FACTORY FILL FLUID TYPE JDM J21A STANDARD CHLOROPRENE | |
TABLE B5 | AGED TEST DATA FROM FACTORY FILL FLUID TYPE CASE MS-1209 STANDARD NITRILE | |
TABLE B6 | AGED TEST DATA FROM FACTORY FILL FLUID TYPE CASE MS-1209 STANDARD CHLOROPRENE | |
TABLE C1 | AGED TEST DATA FROM ASTM REFERENCE OIL #1 STANDARD NITRILE | |
TABLE C2 | AGED TEST DATA FROM FACTORY ASTM REFERENCE OIL #1 STANDARD CHLOROPRENE | |
TABLE C3 | AGED TEST DATA FROM ASTM REFERENCE OIL IRM 903 STANDARD NITRILE | |
TABLE C4 | AGED TEST DATA FROM ASTM REFERENCE OIL IRM 903 STANDARD CHLOROPRENE | |
TABLE D1 | AGED TEST DATA FROM CASE FILL OIL CASE MS-1209 AND DAYCO NITRILE | |
TABLE D2 | AGED TEST DATA FROM CASE FILL OIL CASE MS-1209 AND DAYCO CHLOROPRENE | |
TABLE D3 | AGED TEST DATA FROM CATERPILLAR FILL OIL CAT 8T-9580 AND GATES NITRILE | |
TABLE D4 | AGED TEST DATA FROM CATERPILLAR FILL OIL CAT 8T-9580 AND GATES CHLOROPRENE | |
TABLE D5 | AGED TEST DATA FROM JOHN DEERE FILL OIL JDM J21A AND PARKER NITRILE | |
TABLE D6 | AGED TEST DATA FROM JOHN DEERE FILL OIL JDM J21A AND PARKER CHLOROPRENE | |
TABLE E1 | ECI RESULTS FROM FACTORY FILL FLUIDS, STANDARD FORMULATIONS AND ACTUAL HOSE FORMULATIONS ALSO STANDARD FORMULATIONS TESTED IN ASTM STANDARD FLUIDS | |
TABLE E1 | ECI RESULTS FROM FACTORY FILL FLUIDS, STANDARD FORMULATIONS AND ACTUAL HOSE FORMULATIONS ALSO STANDARD FORMULATIONS TESTED IN ASTM STANDARD FLUIDS | |
TABLE E1 | ECI RESULTS FROM FACTORY FILL FLUIDS, STANDARD FORMULATIONS AND ACTUAL HOSE FORMULATIONS ALSO STANDARD FORMULATIONS TESTED IN ASTM STANDARD FLUIDS | |
TABLE E1 | ECI RESULTS FROM FACTORY FILL FLUIDS, STANDARD FORMULATIONS AND ACTUAL HOSE FORMULATIONS ALSO STANDARD FORMULATIONS TESTED IN ASTM STANDARD FLUIDS |
Issuing Committee
Hydraulic Hose and Hose Fittings Committee
The Hydraulic Hose and Hose Fittings Subcommittee of the FCCTC develops and maintains SAE Standards, Recommended Practices and Information Reports relating to hydraulic hose and hose fittings with an intended use in pressure applications. Participants in the FCCTC Hydraulic Hose and Hose Fittings Subcommittee include OEMs, suppliers, consulting firms, government and other interested parties.
Reference
Number | Title |
---|---|
ASTMD380 | This document is not part of the subscrption. |
ASTMD471 | This document is not part of the subscrption. |
ISO13226 | This document is not part of the subscrption. |
ISO2393 | This document is not part of the subscrption. |
J343_201201 | Test and Test Procedures for SAE 100R Series Hydraulic Hose and Hose Assemblies |
J343_201605 | Test and Test Procedures for SAE 100R Series Hydraulic Hose and Hose Assemblies |
J517_201302 | Hydraulic Hose |
J517_201612 | Hydraulic Hose |
* Redlines comparisons are available for those standards
listed in the Revision History that contain a radio button. A
redline comparison of the current version against a revision is
accomplished by selecting the radio button next to the standard and
then selecting 'compare'. At this time, Redline versions only exist
for some AMS standards. SAE will continue to add redline versioning
with ongoing updates to SAE MOBILUS.