These test procedures were developed based upon the knowledge that steel panel dent resistance characteristics are strain rate dependent. The “quasi-static” section of the procedure simulates real world dent phenomena that occur at low indenter velocities such as palm-printing, elbow marks, plant handling, etc. The indenter velocity specified in this section of the procedure is set to minimize material strain rate effects. The dynamic section of the procedure simulates loading conditions that occur at higher indenter velocities, such as hail impact, shopping carts, and door-to-door parking lot impact.
Three dent test schedules are addressed in this procedure. Schedule A is for use with a specified laboratory prepared (generic) panel, Schedule B is for use with a formed automotive outer body panel or assembly, and Schedule C addresses end product or full vehicle testing. These schedules are targeted at sheet steel samples obtained at different points in an auto/steel product development cycle. A multiple schedule approach has been utilized to maximize dent test method flexibility and thereby allow both the steel producers and end users to benefit from a standardized approach. Extrapolating results from one schedule to another, however, may not be valid and could result in erroneous conclusions.
For “quasi-static” testing, each test schedule provides a load-displacement curve for a given material, either as-stamped or after assembly, under a prescribed set of conditions such as specified strain state, specimen geometry, boundary conditions, indenter type, etc. In order to obtain the most information about dynamic denting behavior comparable in scope to the quasi-static testing, it is necessary to use high speed measuring and recording equipment. If use of this equipment is cost-prohibitive, other dynamic dent evaluations use a drop weight, pendulum, or air gun to fire a projectile at the test surface. For this latter type of dynamic testing, only the impact energy is calculated and the dent depth measured after impact. This information may be sufficient to measure some aspects of dent resistance in the absence of high-speed measuring and recording equipment, but the indenter speed/energy interaction will not be captured. Uniform methods for calculating panel property characteristics such as stiffness and oil canning load are presented. A format for reporting test results is suggested. Using this procedure, reproducible values of “dent resistance” should be obtained in different laboratories.
Rationale
J2575 has been reaffirmed to comply with the SAE five-year review policy.
The Metals Technical Committee (MTC) controls specifications for Ferrous and Non-Ferrous: Metallic Wrought Products, Cast & Sintered Products, Metal Properties & Processes, and Metal Test Procedures. The MTC oversees standards to establish uniform procedures that: 1) establish a common language for the industry to review materials and processes through standards, 2) are reviewed and updated on a regular 5-year basis with coordination to other industry specifications, and 3) creates a common industry interface for technical discussions. The MTC ensures that all standards are developed with qualified personnel to perform respective tasks, meets at least once a year to provide relevant updates to current specifications, and assesses whether new standards are needed by industry. The committee also maintains the public web pages by reviewing and updating the information necessary. The MTC shall report to the Materials Processes and Parts Council (MPPC) on a biannual basis. Participants in the SAE Metals Technical Committee include representatives from OEMs, suppliers, consulting firms, government, and other interested parties.
* Redlines comparisons are available for those standards
listed in the Revision History that contain a radio button. A
redline comparison of the current version against a revision is
accomplished by selecting the radio button next to the standard and
then selecting 'compare'. At this time, Redline versions only exist
for some AMS standards. SAE will continue to add redline versioning
with ongoing updates to SAE MOBILUS.
View/Annotate
Content Loading, Please Wait
Document Preview
Content Loading, Please Wait
Document Comparison
Content Loading, Please Wait
Download
A list of downloadable items.
Product Code
Document Title
File Type
Download
J2575_201504
Standardized Dent Resistance Test Procedure
Export Metadata
This modal will allow the user to download citation information or export specific fields of data into one of three file formats: Excel, comma-separated values, or text.
You are currently not logged into your Dashboard account, which is required for annotating.
Please select Login to login or register for the Dashboard. Select Continue to view the content without the ability to annotate.
Redline Warning
You are currently not logged into your Dashboard account, which is required for annotating.
Please select Login to login or register for the Dashboard. Select Continue to view the content without the ability to annotate.
Data Set Warning
Standardized Dent Resistance Test Procedure
SAE Journal Subscriptions are available in a variety of options, which include electronic, electronic with back file, and archive. For detailed information and options, please complete the following:
Content Request
Check My Access!
You may already have access to the Ground Vehicle Standard, Standardized Dent Resistance Test Procedure
Subscription Access
If you have Subscription Access with a username and password, please login below.
Institutional Login
If you have Institutional Access to SAE MOBILUS, using a predetermined organizational login utilizing single-sign-on (Shibboleth), please login below. To request institutional access to SAE MOBILUS, please complete the institutional subscription information form.
Purchase
If you do not have access to SAE MOBILUS via username/password or institutional access, you can still purchase the Ground Vehicle Standard, Standardized Dent Resistance Test Procedure.
Search Tips: Search Operators:AND, OR, NOT; Wild Cards; Using Quotes
SAE MOBILUS® Search Tips
Please note: All terms not contained within quotes, will be evaluated using the OR operator. This means that your search results will contain all results that contain ANY of the entered terms.
AND, OR, NOT
SAE MOBILUS supports the use of the AND, OR and NOT BOOLEAN operators ONLY function with the Advanced Search.
Wild Cards
Using the asterisk, ( * ) allows you to search for a partial word. For example, entering a keyword search of aero* will search for any word beginning with aero.
Using the question mark, ( ? ) allows you to search for a word with a single character wildcard. For example, searching for t?re would match both tire and tyre
Using Quotes
Words in double quotes " " are treated as a phrase. Conducting a search for "heat model" will return all results in which the exact phrase "heat model" is found, while "heat modeling" would NOT be included.
A term combined with a phrase will be joined with an OR operator.
Searching for Standards
When searching for a standard please use the entire Document Number assigned, which includes the abbreviation. A space can be used, or omitted between the abbreviation and number.