This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
AIR BRAKE HOSE
- Ground Vehicle Standard
- J1402B_197001
- Revised
Sector:
Issuing Committee:
Language:
English
Scope
This specification covers seven types of air hose intended for use in automotive air brake systems. The system includes all air actuated equipment leading from the air brake line. These types of hose are not to be used from the air compressor to air reservoir if air temperature is in excess of 250 F. Type G hose is to be used in frame and cab piping only, and only where air temperature is not in excess of 200 F. The types of hose are as follows:
-
Type A–Hose shall be mandrel built having a tube and friction of oil resisting rubber, reinforced with cotton or synthetic cord or duck plies or a combination of both, and a cover of oil resisting compounds utilizing polymerized chloroprene as the basic material. Assemble with reusable or permanent type metal end fittings.
-
Type B–Hose shall be nonmandrel built having a tube and friction of oil resisting rubber, reinforced with cotton or synthetic cord or duck plies or a combination of both, and a cover of oil resisting compounds utilizing polymerized chloroprene as the basic material. Assemble with reusable or permanent type metal end fittings.
-
Type C–Hose shall be mandrel built having a tube of oil resisting rubber, reinforced with one braid of high tensile steel wire and a cover of oil resisting compounds utilizing polymerized chloroprene as the basic material. A cotton braid or other suitable material may be used to anchor the cover to the hose. Assemble with permanent type metal end fittings only.
-
Type D–Hose shall be mandrel built having a tube of oil resisting rubber, reinforced by two cotton or synthetic braids separated by a wire braid. All braids are to be impregnated with an oil and age resisting compound. The wire braid may be of high tensile carbon steel or of series 300 stainless steel. Hose may also have an optional thin cover of oil resisting compound utilizing polymerized chloroprene as the basic material. Assemble with reusable or permanent type metal end fittings.
-
Class I–The wire braid shall be of high tensile carbon steel.
-
Class II–The wire braid shall be of 300 series stainless steel.
-
-
Type E–Hose shall be mandrel built having a tube of oil resisting rubber, reinforced with two cotton or synthetic braids separated by a wire braid. All braids are to be impregnated with an oil and age resisting compound. This hose is not to be used on any line where abrasion of the outer cover will be encountered in its service. Assemble with reusable type metal end fittings only.
-
Type F–Hose shall be mandrel built having a tube of oil resisting rubber, reinforced with one 300 Series stainless steel braid and one fabric braid separated by an insulation layer of oil resisting rubber. The fabric braid is to be impregnated with an oil and age resistant compound. Assemble with reusable or permanent type metal end fittings.
-
Type G–Hose shall be nonmandrel built having a tube of polyamide nylon reinforced with a braid of polyester or equivalent yarn, and an oil resistant cover of polyamide or polyurethane material containing self-extinguishing flame inhibitors. The polyamide shall have a maximum moisture absorption of 2% at 100% relative humidity and 75 F, and a minimum melting point of 350 F. This hose is intended for inframe and cab piping and for a temperature range of -40 F to 200 F. This hose is not to be used for frame to axle or cab to trailer connections. Assemble with either permanent or reusable type metal end fittings.
CAUTION: This hose is composed in part of thermoplastic materials and must not be used in applications where temperatures may exceed the range shown.
Data Sets - Support Documents
No Datasets Available
Issuing Committee
Hydraulic Hose and Hose Fittings Committee
The Hydraulic Hose and Hose Fittings Subcommittee of the FCCTC develops and maintains SAE Standards, Recommended Practices and Information Reports relating to hydraulic hose and hose fittings with an intended use in pressure applications. Participants in the FCCTC Hydraulic Hose and Hose Fittings Subcommittee include OEMs, suppliers, consulting firms, government and other interested parties.
Reference
Number | Title |
---|
* Redlines comparisons are available for those standards
listed in the Revision History that contain a radio button. A
redline comparison of the current version against a revision is
accomplished by selecting the radio button next to the standard and
then selecting 'compare'. At this time, Redline versions only exist
for some AMS standards. SAE will continue to add redline versioning
with ongoing updates to SAE MOBILUS.