AS5869A: FITTING ASSEMBLY, UNION, 3 HOLE FLANGE, AXIALLY SWAGED, HYDRAULIC, 5080 PSI

Features

Issuing Committee: G-3, Aerospace Couplings, Fittings, Hose, Tubing Assemblies

Scope

Content: No Scope available

Rationale

Content

REVISED TO ADD FLANGE OPTIONAL MATERIAL, OPTIONAL LENGTH AND UPDATED NOTE 8 & 12

/1/

MATERIALS:

CODE LETTER "T"

RING	-	AMS 4965 TITANIUM ALLOY, 6.0AL 4.0V SOLUTION HEAT TREATED AND AGED OR AMS 4928 TITANIUM ALLOY 6.0 AL 4.0V ANNEALED WITH HIGH STRENGTH CARBON FIBER/EPOXY RESIN COMPOSITE REINFORCEMENT.
BODY	-	AMS 4928 TITANIUM ALLOY, 6.0AL 4.0V ANNEALED
FLANGE	-	OPTIONAL MATERIAL AMS 4911 TITANIUM ALLOY, 6.0AL 4.0V ANNEALED

2
FINISH:

TITANIUM - NONE REQUIRED

/3/

COATINGS/LUBRICANTS:

RING	-	THE OUTER SURFACE SHALL HAVE A .125" MINIMUM WIDTH BLUE COLORED RING OR COMPLETELY COLORED BLUE TO INDICATE 5080 PSI MAXIMUM OPERATION PRESSURE. AN AS1241 FLUID RESISTANT PTFE COATING OR PAINT MUST BE USED.
BODY	-	SOLID FILM LUBRICANT PER AS5272, TYPE I OR II, PTFE OR PETROLEUM-BASED LUBRICANT MAY BE APPLIED TO PORTIONS OF THE ID AND OD. THE PETROLEUM-BASED LUBRICANT SHALL NOT BE IN CONTACT WITH THE SYSTEM FLUID.

/4/
ALL PRODUCTS SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST FOR PRI-QPL-AS5958 FOR THIS STANDARD. SEE HTTP:WWW.PRI.SAE.ORG/QPL/AS595B.PDF FOR CURRENT QPL ONLINE.
5
DIMENSIONS AND TOLERANCES NOT DEFINED ON THIS STANDARD SHALL BE SPECIFIED AND CONTROLLED BY THE MANUFACTURER. THE MANUFACTURER IS RESPONSIBLE TO ENSURE COMPLIANCE WITH THE PROCUREMENT SPECIFICATION.
/6/
IDENTIFICATION SHALL BE IN ACCORDANCE WITH AS5958 AND SHALL BE IDENTIFIED ON RING IN THE AREA SHOWN.
7
FITTINGS SHALL BE INSTALLED IN ACCORDANCE WITH AS5959.
8
SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 uin RA. FORGED SURFACES TO BE 250 uin Ra.
9
DIMENSIONS AND TOLERANCES SHALL BE IN ACCORDANCE WITH AMERICAN SOCIETY OF MECHANICAL ENGINEERS, ASME Y14.5M-1994.
1. a
  DIMENSIONS ARE IN INCHES UNLESS OTHERWISE SPECIFIED
2. b
  DIMENSIONAL TOLERANCES SHALL BE +-.005 INCHES UNLESS OTHERWISE SPECIFIED
3. c
  ANGULAR TOLERANCES SHALL BE +/-0.50 DEGREES UNLESS OTHERWISE SPECIFIED
4. d
  BREAK ALL EDGES .003-.010 INCHES UNLESS OTHERWISE SPECIFIED
10
INTREPRETATION OF DRAWING PER AS4296
/11/
THIS DIMENSION IS THE ALLOWABLE TUBE END POSITIONING FOR SYSTEM LAYOUT DESIGN.
/12/
FLANGE MAY BE WELDED TO THE BODY. THE WELD SHALL BE A MINIMUM 13" WELD, CLASS B ON ONE SIDE IN ACCORDANCE WITH IAW AWS D17.1
/13/
14
THE CHANGE BAR ( | ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT.

Meta Tags

Topics: Parts
Hoses and tubes
Titanium alloys
Heat treatment
Fittings
Nanomaterials
Coatings, colorants and finishes
Fibers
Polymers
Composite materials
Hydraulic fittings

Details

DOI: https://doi.org/10.4271/AS5869A

Pages: 3

Citation: SAE International Technical Standard, FITTING ASSEMBLY, UNION, 3 HOLE FLANGE, AXIALLY SWAGED, HYDRAULIC, 5080 PSI, SAE Standard AS5869A, Revised November 2006, Issued February 2006, https://doi.org/10.4271/AS5869A.

Additional Details