This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Enhancement of Near Wall Mixing of an Impinging Jet by Means of a Bump on the Wall
Annotation ability available
Sector:
Language:
English
Abstract
It is found that a thin and rich mixture layer on a wall is formed after impingement of a gas jet of fuel on the wall. The measured thickness of the mixture layer is about 2 mm. and its dispersion rate after the end of injection is much lower, compared to that of a space gas jet. This phenomenon in a small D.I. diesel engine is known as “wall wetting” or “wall fuel accumulation” which has an important influence on engine fuel consumption and emissions.
This paper presents a technique for enhancing the near wall mixing of an impinging jet by means of a bump on the wall. The development of a wall jet formed after an impingement of a gas jet has been investigated by simultaneously measuring the near wall velocity and concentration distribution. It has been found that a wall jet is stripped off the wall and ejected as a secondary jet when the wall jet encounters a bump of the wall. Effects of the bump height, the location of the bump and the impingement angle are studied at a number of typical conditions. The distributions of velocity and concentration of a secondary jet are also investigated in detail and the non-dimensional distributions for velocity and concentration of a secondary jet are derived based on the data statistics. In addition the concept of concentration mean dispersion rate is employed in data processing in order to understand the effects of the bump geometry on mixing rate. It has experimentally confirmed that a controllable mixing process of “space-wall-space” for an impinging jet may be realized by means of a bump setting on the wall.
Authors
Citation
Su, W., Lin, R., Xie, H., and Shi, S., "Enhancement of Near Wall Mixing of an Impinging Jet by Means of a Bump on the Wall," SAE Technical Paper 971616, 1997, https://doi.org/10.4271/971616.Also In
References
- Change Y.I. et al. “A Photographic Study of Soot Formation and Combustion in a Diesel Flame with a Rapid Compression Machine” Proceeding of COMODIA 149 158 1985
- Balakin V.L. et al. “Principles of Making High Economic Low Toxic Combustion Process in High Speed Diesel Engine” 18th CIMAC D155 1989
- Shi Shao-xi Su Wanhua Zhao Kuihan Yue Yong “Development of a Four-zone Analytical Combustion Model for a D.I. Compress Ignition Engine” 20th CIMAC D13 1993
- Matsui Y. et al “Sources of Hydrocarbon Emissions from a Small Direct Injection Diesel Engine” SAE Review 7 1986
- Tsunenoto H. “The Behavior of Impinged Fuel Spray on Simulated Combustion Chamber Walls in Direct Injection Diesel Engines” JSAE Review 3 1982
- Morris C.J. Dent J.C. “the Simulation of Air Fuel Mixing in High Swirl Open Chamber Diesel Engines” Proc. I.M.E 190 47 46 1976
- Arcomanis C. et al. “Velocity and Concentration Measurement in a Model Diesel Engines” Experimental in Fluids 3 270 276 1985
- Chen, A.J. Lightntean et al. “Simultaneous Velocity and Concentration of Turbulence Jet Flows” 10th Ninth Symp. on Turbulence 1984
- tanabe Hideaki Sato G. Takeshi “Experimental Study on Unsteady Wall Impinging Jet” SAP Paper 900605 1990
- Su Wanhua Xie Hui Lin Rongwen Shi Shao-xi “Experimental Study on the Effects of Spray Impingement and Turbulence Structure on Spray Mixing Rate by Gas Jet Simulation” SAE Paper 960775 1996
- Peters N. Combustion Sci. Tech. 30 1 17 1983
- Bilger R. W. “Turbulent Diffusion Flames” Ann. Rev. Fluid Mech. 1989 21 101 35
- Masri A. R. Bilger R. W. “The Local Structure of Turbulent Nonpremixed Flames Near Extinction” Combustion and Flame 81 260 276 1990
- Namazian M. Schefer R. W. Kelly J. “Scalar Dissipation Measurements in the Developing Region of a Jet” Combustion and Flame 74 147 160 1988