This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
LIF and Flame-Emission Imaging of Liquid Fuel Films and Pool Fires in an SI Engine During a Simulated Cold Start
Annotation ability available
Sector:
Language:
English
Abstract
Video imaging has been used to investigate the evolution of liquid fuel films on combustion chamber walls during a simulated cold start of a port fuel-injected engine. The experiments were performed in a single-cylinder research engine with a production, four-valve head and a window in the piston crown. Flood-illuminated laser-induced fluorescence was used to observe the fuel films directly, and color video recording of visible emission from pool fires due to burning fuel films was used as an indirect measure of film location.
The imaging techniques were applied to a comparative study of open and closed valve injection, for coolant temperatures of 20, 40 and 60 °C. In general, for all cases it is shown that fuel films form in the vicinity of the intake valve seats. For closed valve injection, films also form below the intake valves and below the squish region between the intake valves and the cylinder wall, while for open valve injection additional fuel films form below the exhaust valves. It is expected that fuel films on the head near the exhaust valves are a direct source of unburned hydrocarbon emissions, that fuel films on the cylinder wall are a source of fuel blowby into the crankcase, and that pool fires are a source of soot.
Recommended Content
Authors
Topic
Citation
Witze, P. and Green, R., "LIF and Flame-Emission Imaging of Liquid Fuel Films and Pool Fires in an SI Engine During a Simulated Cold Start," SAE Technical Paper 970866, 1997, https://doi.org/10.4271/970866.Also In
References
- Takeda, K. Yaegashi, T. Sekiguchi, K. Saito, K. “Mixture Preparation and HC Emissions of a 4-Valve Engine with Port Fuel Injection During Cold Starting and Warm-up,” SAE Paper No. 950074 1995
- Kosowski, M. G. “Soot Formation in a Multipoint-Fuel-Injected Spark-Ignited Engine,” Trans. SAE 94 786 1985
- Quader, A. A. “How Injector, Engine, and Fuel Variables Impact Smoke and Hydrocarbon Emissions with Port Fuel Injection,” Trans. SAE 98 327 1989
- Fry, M. D. Nightingale, C. J. E. “Use of High-Speed Photography to Study In-Cylinder Mixture Preparation on a Four-Valve SI Engine,” Proceedings of IMechE Seminar on Measurement and Observation Analysis of Combustion in Engines,” 85 1994
- Fry, M. Nightingale, C. Richardson, S. “High-Speed Photography and Image Analysis Techniques Applied to Study Droplet Motion within the Porting and Cylinder of a 4-Valve SI Engine,” SAE Paper No. 952525 1995
- Hardalupas, Y. Taylor, A. M. K. P. Whitelaw, J. H. Ishii, K. Miyano, H. Urata, Y. “Influence of Injection Timing on In-Cylinder Fuel Distribution in a Honda VTEC-E Engine,” SAE Paper No. 950507 1995
- Shin, Y. Cheng, W. K. Heywood, J. B. “Liquid Gasoline Behavior in the Engine Cylinder of a SI Engine,” SAE Paper No. 941872 1994
- Saito, K. Sekiguchi, K. Imatake, N. Takeda, K. Yaegashi, T. “A New Method to Analyze Fuel Behavior in a Spark lgnition Engine,” SAE Paper No. 950044 1995
- Nogi, T. Ohyama, Y. Yamauchi, T. Kuroiwa, H. “Mixture Formation of Fuel lnjection Systems in Gasoline Engines,” SAE Paper No. 880558 1988
- Nogi, T. Ohyama, Y. Yamauchi, T. “Effects of Mixture Formation of Fuel lnjection Systems in Gasoline Engine,” SAE Paper No. 891961 1989
- Ohyama, Y. Ohsuga, M. Kuroiwa, H. “Study of Mixture Formation and lgnition Process in Spark lgnition Engine Using Optical Combustion Sensor,” Trans. SAE 99 2002 1990
- Ohyama, Y. Nogi, T. Ohsuga, M. “Effects of FuelIAir Mixture Preparation on Fuel Consumption and Exhaust Emission in a Spark lgnition Engine,” lMech E Paper C389/232 59 1992
- Song, K. Clasen, E. Chang, C. Campbell, S. Rhee, K. T. “Post-Flame Oxidation and Unburned Hydrocarbon in a Spark-Ignition Engine,” SAE Paper 952543 1995
- Werlberger, P. Rokita, R. Chmela, F. “Observation of Fuel lnjection and Combustion by Use of an Endoscopic Video System,” Proceedings of IMechE Seminar - Measurement and Observation Analysis of Combustion in Engines 39 1994
- Felton, P. G. Kyritsis, D. C. Fulcher, S. K. “LIF Visualization of Liquid Fuel in the Intake Manifold During Cold Start,” SAE Paper No. 952464 1995
- Bowditch, F. W. “A New Tool for Combustion Research: A Quartz Piston Engine,” Trans. SAE 69 17 1961
- Sunnarborg, D. A. Sandia National Laboratories 1996
- Bates, S. C. “A Transparent Engine for Flow and Combustion Visualization Studies,” SAE Paper No. 880520 1988
- Espey, C. Dec, J. E. “Diesel Engine Combustion Studies in a Newly Designed Optical-Access Engine Using High-Speed Visualization and 2-D Laser Imaging” SAE Paper No. 930971 1993
- Xybion Electronic Systems Corporation “Electronically Gated Intensified CCD Video Camera User's Manual, Model ISG-350,” 1992
- Witze, P. 0. Green, R. M. “LIF Visualization of Liquid Fuel in the Cylinder of a Spark lgnition Engine,” Proceedings of the Eighth International Symposium on Applications of Laser Techniques to Fluid Mechanics Lisbon, Portugal July 1996
- Asmus, T. Chrysler Corporation 1996
- Dodge, L. G. “Fuel Preparation Requirements for Direct-Injected Spark-Ignition Engines,” SAE Paper No. 962015 1996
- Brown, C. N. Ladommatos, N. “A Numerical Study of Fuel Evaporation and Transportation in the Intake Manifold of a Port-Injected Spark-Ignition Engine,” Proc. IMechE, Journal of Automobile Engineering 205 161 1991