This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
An Experimental and Predictive Study of the Flow Field in Axisymmetric Automotive Exhaust Catalyst Systems
Annotation ability available
Sector:
Language:
English
Abstract
An experimental and theoretical investigation has been performed on the flow and pressure loss in axisymmetric catalytic converters and isolated monoliths under steady, isothermal flow conditions. Monolith resistance has been measured with a uniform, low turbulence, incident flow field. It has been found that the pressure loss expression for fully developed laminar flow is a good approximation to observations for x+ greater than 0.2. However, for x+ less than 0.2 the additional pressure loss due to developing flow is no longer negligible and a better approach is to use the correlation proposed by Shah (16). From experimental studies on the axisymmetric catalytic converters non-dimensional power law relationships have been derived relating maldistribution and pressure drop to expansion length, Re, and monolith length. These expressions are shown to generally fit the data well within ±5%. CFD predictions of the flow for a wide range of geometric configurations and flow conditions have shown that generally the system non-dimensional pressure loss can be predicted to within about 10% but that the maldistribution index is underpredicted within a range of 9-17.5%. It is believed that the pressure loss expression derived from 1-D flow studies is too simplistic. CFD predictions do, however, show the same pattern of change as observed experimentally and hence their performance in predicting trends is quite encouraging.
Recommended Content
Authors
Citation
Benjamin, S., Clarkson, R., Haimad, N., and Girgis, N., "An Experimental and Predictive Study of the Flow Field in Axisymmetric Automotive Exhaust Catalyst Systems," SAE Technical Paper 961208, 1996, https://doi.org/10.4271/961208.Also In
References
- Comfort, E. H. “Monolithic catalytic converter performance as a function of flow distribution,” ASME Winter Annual Meeting, Paper No. 74-WA/HT-30 1974
- Howitt, J. S. Sekella, T. C. “Flow effects in monolithic honeycomb automotive catalytic converters,” SAE Paper 740244 1974
- Lemme, J. S. Sekella, T. C. “Flow through catalytic converters-An analytical and experimental treatment,” SAE Paper 740243 1974
- Lai, M.-C. Kim, J.-Y. Cheng, C.-Y., P. Chui, G. Pakko, J. D. “Three-dimensional simulations of automotive catalytic converter internal flow,” SAE Paper 910200 1991
- Kim, J. Y. Lai, M. C. Li, P. Chui, G. “Modelling diffuser-monolith flows and its implications to automotive catalyst converter design,” SAE Paper 921093 1992
- Bella, G. Rocco, V. Maggiore, M. “A study of inlet flow distortion effects on automotive catalytic converters,” ASME Journ. of Eng. for Gas Turbines and Power 113 419 426 1991
- Wendland, D. W. Matthes, W. R. “Visualisation of automotive catalytic converter internal flows,” SAE Paper 861554 1986
- Wendland, D. W. Sorrell, P. L. Kreucher, J. E. “Sources of monolith catalytic converter pressure loss,” SAE Paper 912372 1991
- Wendland, D. W. Matthes, W. R. Sorrell, P. L. “Effect of header truncation on monolith converter emission-control performance,” SAE Paper 922340 1992
- Will, N. S. Bennet, C. J. “Flow maldistributions in automotive converter canisters and their effect on emission control,” SAE Paper 922339 1992
- Weltens, H. Bressler, H. Terres, F. Neumaier, H. Rammoser, D. “Optimisation of catalytic converter gas flow distribution by CFD predictions,” SAE Paper 930780 1993
- Clarkson R. J. “A theoretical and experimental study of automotive catalytic converters,” Coventry University 1995
- Schlichting, H. Boundary-Laver Theory 7th McGraw-Hill 1979
- Heitor, M. V. Rodrigues, J. M. “Intercomparison of flow measurements,” Technical University of Lisbon, Department of Mechanical Engineering May 1992
- Borger, G.-G. 23 45 50 1975
- Shah, R. K. “A correlation for laminar hydrodynamic entry length solutions for circular and noncircular ducts,” Journal of Fluids Eng. 100 177 179 June 1978
- Computational Dynamics STAR-CD Users Guide -Version 2.2 1994
- Clarkson, R. J. Benjamin S. F. Girgis, N. S. Richardson, S. “Theoretical and experimental investigation of the flow in catalytic converters,” IMechE Seminar on the Validation of Computational Techniques in Vehicle Design April 1994
- Norris, L. H. Reynolds, W. C. “Turbulent channel flow with a moving wavy boundary,” Department of Mechanical Engineering, Stanford University 1975