This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Geometric optimization of Nozzles for Inclined Injectors for DI Diesel Engines
Annotation ability available
Sector:
Language:
English
Abstract
Low emission heavy-duty diesel engines are increasingly utilizing four-valve designs with vertical central injectors. However, two-valve DI diesel engines with inclined injectors offset from the centerline of the piston bowl are likely to continue to be used in medium and light duty applications for some time. In such situations, designing of the hole-type nozzle is very difficult and may cause unavoidable back-drilling problems. The purpose of this paper is to solve back-drilling problems connected with hole-type nozzles and improve fuel-air mixing which leads to more efficient combustion. Based on geometric considerations, this paper introduces single-cone hole-type nozzles, double-cone hole-type nozzles, and the critical principal angles for hole-type nozzles. The single-cone hole-type nozzles and double-cone hole-type nozzles can meet requirements for height of the spray impingement points and spray orifice distribution angle at the same time. The concept of the critical principal angle for hole-type nozzles provides a criterion for the determination of both the hole-type nozzle angles and the injector installation angle.
This paper also gives an example to illustrate the application of the above methods. Finally, this paper systematically summarizes design methods for hole-type nozzles that fit the DI combustion chamber.
Citation
Chen, Y. and Kittelson, D., "Geometric optimization of Nozzles for Inclined Injectors for DI Diesel Engines," SAE Technical Paper 960868, 1996, https://doi.org/10.4271/960868.Also In
References
- Kuo, T. Yu R. C. Shahed S. M. “A Numerical Study of the Transient Evaporating Spray Mixing Process in the Diesel Environment” SAE paper No. 831735 , SAE Trans. 92 1983
- Walker, Jonathan “L'orange Prospers and Grows at the Turn of the Diesel Century” Diesel & Gas Turbine December 1993
- Sami, Hiroshi Tetsu Watanabe etc. “A Study on the Effects of High Pressure Injection for the Combustion of Small DI Diesel Engine” Japanese Journal Internal Combustion Engines 30 384 10 1991
- Xu, Min Nishida Keiya Hiroyasu Hiroyuki “A Practical Calculation Method for Injection Pressure and Spray Penetration in Diesel Engines” SAE paper No. 920624 1992
- Takamura, Akio Ohta Takashi Fukushima Susumu Kamimoto Takeyuki “A Study on Precise Measurement of Diesel Fuel Injection Rate” SAE paper No. 920630 1992
- Megahed, M. “First Measurements of the Liquid Phase Temperature in Diesel Sprays” SAE paper No, 930969 1993
- Song, Y. C. Shi F. M. Gao X. Y. Yan F. C. Chen J. H. “The Laser Interfero-Holographic and Tomographic Analysis of Concentration and Temperature Distribution of a Three Dimensional Transient Diesel Spray” SAE paper No. 941756 1994
- Yoshizaki, Takuo Nishida Keiya Hiroyasu Hiroyasu Song Kyu-Keun “Three-Dimensional Spray Distribution in a Direct Injection Diesel Engine” SAE paper No. 941693 1994
- Gong, Yunyi Li Xianguo Peng Zhijun Bai Xingyan “Number-Based Droplet Velocity Distribution in High Pressure Diesel Sprays” SAE paper No. 941689 1994
- Rao, K. K. Winterbone D. E. Clough E. “Influence of Swirl on High Pressure Injection in Hydra Diesel Engine’ SAE paper No. 930978 1993
- Sun, Jimei Dong Yu Xu Yong Taso K. C. “In Cylinder Gas Motions Via Non-isotropic Turbulent Modeling and Experiment” SAE paper No. 891915 1989
- Jane, P. A. H. Brear F. “The Development of a Direct Injection Diesel Combustion System for Low Noise, Emissions and Mechanical Loading” Journal of Automobile Engineering 203 D4 1989
- Tanabe, Hideaki Sato G. Takeshi “Experimental Study on Unsteady Wall Impinging Jet” SAE paper No. 900605 1990
- Gale, F. Nigel “Diesel Engine Design for Cleaner Air” Technology Today Southwest Research Institute 1989
- Singal, S. K. Pundir B. P. Mehta P. S. “Modeling Spray/wall Interaction in Swirling Flows for DI Diesel Engines” Journal of Automobile Engineering 204 D4 1990
- Date, Kenji Manabe Masami Kano Hiroyuki Kato Masaaki Oya Takio “Contribution of Fuel Flow Improvement in Nozzle to Spray Formation” SAE paper No. 920622 1992
- Dodge, G. Lee Ryan Thomas W. III Ryan Michael G. “Effects of Different injector Hole Shapes on Diesel Sprays” SAE paper No. 920623 1992
- Bosch “Diesel Fuel Injection-Proven Technology, New Ideas, Modern Production” Robert Bosch GmbH 1987
- Bosch “Diesel Fuel Injection- an Overview-Technical Instruction” Robert Bosch GmbH 1990
- Tolan, Lewis E. Hess, Thomas D. Stanadyne, Inc., Diesel Systems Group “The Pencil Nozzle-- Past, Present & Future” SAE paper No. 830666 1983
- Sczomak, P. David “The Poppet Covered Orifice Fuel Injection Nozzle” SAE paper No. 900821 1990
- Ogura, Masaru Liu Bai-Fu Daidoji Susumu Ikeda Yoshio “Study on DI Diesel Engine with an Impinging Nozzle Head - An Effect of Shape of Impinging Nozzle Head (NICS)” SAE paper No. 920625 1992
- Ziejewski, Mariusz Goettler Hans J. “Fuel-Air Injection Nozzle for Diesel Engines” SAE paper No. 891944 1989
- Wang, Guangchun Zhen Huang Long Zhugao “The Net of Fuel Sprays and Calculation for Medium and Small DI Combustion Chambers” Tractor 4 1986
- Tsao, K. C. Dong Y. Xu Y. “Matching of Engine Chamber and Fuel Supply System via KIVA- II Modeling” NIST Special Publication 1991
- Hou, Zhi-xin Kizawa Hirofumi “Effects of Combustion Chamber Geometries on In-cylinder Flow Motion and Exhaust Emission in a Direct Injection Diesel Engine” 10th Joint Symposium on Internal Combustion Engine Yokohama, Japan 1992
- Lilly, L C R “Diesel Engine Reference Book” 1984
- Heywood, B. John “Internal Combustion Engine Fundamentals” 1988
- Ladommatos, N. Balian R. A. “Combustion in a Direct Injection Diesel Engine with Increased Clearance Volume” Journal of Automobile Engineering 204 D3 1990
- Chen, Yong “Design of the Multi-hole Nozzle Holder Tip” Chinese Internal Combustion Engine Engineering 1 8 1987
- BOSCH “Nozzles and Nozzle-Holder Assemblies” Robert Bosch GrnbH 1980