This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Transient Air Flow Rate Estimation in a Natural Gas Engine Using a Nonlinear Observer
Annotation ability available
Sector:
Language:
English
Abstract
Stoichiometric air-fuel ratio control during transient operation requires an accurate estimate or measurement of the instantaneous air flow rate in an engine. Two methods are commonly used for determining engine air flow rate: air-mass sensing and conventional “speed-density.” The lead air flow information provided by air-mass sensors helps compensate for manifold filling and other fuel system delays. However, the high cost (and sometimes lower reliability) of air-mass sensors has led many manufacturers to continue to use the less accurate speed-density method for determining air flow rate.
This paper develops a model-based nonlinear manifold pressure observer that estimates the flow rates at the throttle and the intake ports of an engine using speed-density type sensors. The throttle flow rate estimate can be used instead of an air-mass sensor to provide the lead information necessary for accurate transient air-fuel control on TBI engines. The intake port flow rate estimate can be used on PFI engines to provide filtered approximations of port flow rates that do not contain phase lag. The estimates are achieved by embedding a simplified throttle and intake manifold model into the controller. Flow estimates are corrected in real-time by comparing a prediction of manifold pressure to measured manifold pressure.
The observer's performance is simulated on a mean value, throttle-body-injected, natural-gas engine model. The elimination of wall wetting dynamics in this type of engine makes it an ideal candidate for the nonlinear observer presented here. Similar results could be expected with gasoline engines, although compensation for liquid fuel dynamics poses additional difficulties.
Simulation results indicate that air-fuel control similar to that of a fast air-mass sensor can be achieved using the nonlinear observer. Although not presented here, versions of the observer have been successfully implemented on V8 engines with significantly different manifold filling characteristics. The computational complexity of the observer is simple enough to allow implementation on current eight bit engine controllers.
Recommended Content
Technical Paper | A Novel Start Algorithm for CNG Engines Using Ion Sense Technology |
Technical Paper | Effect of Fuel Composition on the Operation of a Lean Burn Natural Gas Engine |
Ground Vehicle Standard | Preignition Rating of Spark Plugs |
Authors
Topic
Citation
Weeks, R. and Moskwa, J., "Transient Air Flow Rate Estimation in a Natural Gas Engine Using a Nonlinear Observer," SAE Technical Paper 940759, 1994, https://doi.org/10.4271/940759.Also In
References
- Hendricks, E. Vesterholm, T. Sorenson, S. C. “Nonlinear, Closed-loop, SI Engine Control Observers,” SAE paper No. 920237 1992
- Kaidantzis, P. et al. “Advanced Nonlinear Observer Control of SI Engines,” SAE paper 930768 1993
- Chang, C. Fekete, N.P. Powell, J.D. “Engine Air-Fuel Ratio Control Using an Event-Based Observer,” SAE paper 930766 1993
- Kao, M.H. Moskwa, J.J. “Nonlinear Sliding Engine Load and Equivalence Ratio Observers,” 1994 American Control Conference Baltimore, MD June 1994
- Shiao, Y.J. Moskwa, J.J. “Cylinder Pressure and Combustion Heat Release Estimation for SI Engine Diagnostics Using Nonlinear Sliding Observers,” 1994 American Control Conference Baltimore, MD June 1994
- Kao, M.H. Moskwa, J.J. “Nonlinear Cylinder and Intake Manifold Pressure Observers for Engine Control and Diagnostics,” 1994 SAE International Congress and Exposition Detroit, MI February 1994
- Kao, M.H. Moskwa, J.J. “Nonlinear Diesel Engine Control and Cylinder Pressure Observation,” ASME J. of Dynamic Systems, Measurement and Control March 1993 1993 ASME Winter Annual Meeting New Orleans, LA November 1993
- Taylor, C.F. The Internal Combustion Engine in Theory and Practice 2nd M.I.T. Press 1985
- Moskwa, J.J. “Automotive Engine Modeling for Real-time Control,” Department of Mechanical Engineering, M.I.T 1988
- Cho, D. “Nonlinear Control Methods for Automotive Powertrain Systems,” Department of Mechanical Engineering, M.I.T 1987
- Moskwa, J.J. Hedrick, J.K. “Automotive Engine Modeling for Real-time Control Application,” Proc. American Contr. Conf. 341 346 1987
- Moskwa, J.J. Hedrick, J.K. “Modeling and Validation of Automotive Engines for Control Algorithm Development,” ASME WAM Advanced Automotive Technologies 13 Karmel, A.M. et. al 1989
- Cho, D. Hedrick, J.K. “Automotive Powertrain Modeling for Control,” ASME J. of Dynamic Systems, Measurement and Control 114 4 568 576 1989
- Weeks, R.W. “Implementation Issues in Sliding Mode Automotive Powertrain Controllers,” Department of Mechanical Engineering, M.I.T. 1988
- Moskwa, J.J. Hedrick, J.K. “Sliding Mode Control of Automotive Engines,” Proc. American Contr. Conf. 2 1040 1045 1989
- Green, J.H. Hedrick, J.K. “Nonlinear Speed Control for Automotive Engines,” Proc. American Contr. Conf. 1990
- Choi, S-B. Hedrick, J.K. “Experimental Implementation of Sliding Controls on Automotive Engines,” Proc. American Contr. Conf. 1992
- McMahon, D.H. et al. “Longitudinal Vehicle Controllers for IVHS: Theory and Experiment,” Proc. American Contr. Conf. 1992
- Heywood, J.B. Internal Combustion Engine Fundamentals McGraw-Hill 1988
- Åström, K.J. Wittenmark, B. Computer Controlled Systems Theory and Design Prentice-Hall 1984
- Chow, E.Y. Willsky, A.S. “Analytic Redundancy and the Design of Robust Failure Detection Systems,” IEEE Trans, on Auto-Control 29 7 603 614 1984
- S IMULINK User's Guide The Math Works, Inc. April 1993
- Dobner, D.J. “A Mathematical Engine Model for Development of Dynamic Engine Control,” SAE paper 800054 1980
- Hendricks, E. Sorenson, S.C. “Mean Value Modeling of Spark Ignition Engines,” SAE paper No. 900616 1990
- Hendricks, E. Vesterholm, T. “The Analysis of Mean Value SI Engine Models,” SAE paper No. 920682 1992