This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Advanced Heat Engines for Range Extender Hybrid Vehicles
Annotation ability available
Sector:
Language:
English
Abstract
A great deal of interest has been expressed recently in hybrid electric vehicles, both for their potential for reduced environmental impacts as well as their increased range over electric-only vehicles. Several organizations have initiated programs to design and evaluate a specific type of hybrid vehicle, the Range Extender Vehicle (REV). Based upon this industry activity, the U.S. Department of Energy's Electric and Hybrid Propulsion Division commissioned the two-phase study which serves as the basis of this paper.
A range extender vehicle is a hybrid vehicle, where a small engine generator (a “genset”) is added to a basic electric vehicle design. This genset “sustains” vehicle operation beyond the range provided by the batteries. The additional weight of the genset and fuel is balanced by the removal of some of the vehicle's batteries. Such a concept may be useful in the near term, when commercially available batteries are not expected to have adequate specific energy to provide the range necessary for market acceptability.
In Phase I, the range extender designs were based on existing, well-characterized electric vehicle designs. Established driving cycles were used to define the basic energy and power needs of the vehicle systems. The emphasis during this initial effort was placed on near-term designs. These designs were based on the use of existing vehicle platforms (Ford Taurus, Dodge Caravan, and Chevrolet C1500 pickup), available lead acid batteries, and primarily small, off-the-sheff engine generator systems.
The primary performance requirement for Phase I was a minimum generator-set-only top speed of 25 mph (40 km/h). This was done for two reasons. First, it followed the rationale used by several organizations, which indicated that a 6 to 10 kWe generator set would be appropriate for the REV configuration. Second, it provided a useful starting point for REV analysis, yielding a lower bound for potential performance.
The Phase II analysis, which is the basis for this paper, evaluated higher performance REV conceptual designs. National Highway Traffic Safety Administration (NHTSA) standards for electric vehicles as well as development requirements for the Ford ETX-II and Modular Electric Vehicle Programs were used to provide the basis for comparison. These included acceleration, speed at grade, and minimum top speed requirements. In all cases, these desired levels of performance indicated that significantly larger generator sets would be required, estimated to be in the 25-50 kWe range. These requirements dictated the use of more advanced engine technologies. A number of engine types and sizes were examined for application to the REV, including advanced four-stroke, two-stroke, gas turbine, rotary, Stirling, and compression ignition engines. The engines selected for analysis ranged from 24 kWe to nearly 63 kWe, at the operating points selected.
Overall, the Phase II analysis demonstrated that higher-performance REVS could be developed, using more advanced heat engine/generator configurations. This higher performance should appeal to a broader range of potential users (than the Phase I design), increasing the REV's potential market penetration.
Recommended Content
Technical Paper | Hybrid Vehicle Gas Turbines |
Technical Paper | Low-Emission Range Extender for Electric Vehicles |
Technical Paper | Gas Turbine Generator Sets for Hybrid Vehicles |
Authors
Topic
Citation
Gelman, D. and Perrot, T., "Advanced Heat Engines for Range Extender Hybrid Vehicles," SAE Technical Paper 930041, 1993, https://doi.org/10.4271/930041.Also In
References
- “1991 Market Data Book,” Automotive News May 29 1991
- Amann, C.A. “The Automotive Engine - A Future Perspective,” SAE No. 891666 General Motors Research Laboratories August 1989
- “The Automotive Stirling Engine,” Mechanical Technology Incorporated 1992
- “CDS2 Two-Stroke Engine,” General Motors 1990
- Cook, J. “Orbital Engine Gathers Speed,” Chartered Mechanical Engineer September 1987
- Deere Technologies International, Inc. Rotary Engine Division 1989
- Gelman, D.J. Perrot, T.L. “The Range Extender Vehicle Concept Study - Final Report,” EA Engineering, Science, and Technology, Inc. June 1992
- “High-Power-Density Kinematic Stirling Engine (Hermetic),” Mechanical Technology Incorporated 1992
- “Hybrid Vehicle Power Module,” Mechanical Technology Incorporated 1992
- Jones, C. “Stratified Charge Rotary Engine Developments at JDTI from 1984 to 1991,” SAE No. 920310 John Deere Technologies International, Inc. February 1992
- Kato, S. Onishi, S. “Glow Plug Assisted Direct Injection Methanol Engine by Impingement of Fuel Jet (OSKA-F),” Nippon Clean Engine Laboratory Co. 9th International Symposium on Alcohol Fuels April 9 12 1991
- Kidwell, JR. “Garrett Multipurpose Small Power Unit (MPSPU) - Program Status 1989,” SAE No. 892251 Allied-Signal Aerospace Co. Garrett Auxiliary Power Division 1989
- Kinematic Program Briefing Mechanical Technology Incorporated 1992
- Letter to David Gelman, EA Engineering Upham Stephen III Mechanical Technology Incorporated April 23 1992
- Mount, R.E. LaBouff, G.A. “Advanced Stratified Charge Rotary Engine Design,” SAE No. 890324 John Deere Technologies International, Inc. Rotary Engine Division 1989
- Orbital Engine Company Brochure 1987
- Simanaitis, D. “Two-Stroke Engines - Great Diversity, Great Potential,” Road and Track December 1990
- “Stirling Engine Emissions Test Results on Natural Gas Fuels - Status Report,” Mechanical Technology Incorporated 1992
- “Stirling Engine Natural Gas Combustion Demonstration Program,” Mechanical Technology Incorporated 1991
- Thomson, M.W. et al. “General Motors 2.3-L Quad 4 Engine,” SAE No. 870353 Buick-Oldsmobile-Cadillac Powertrain Group 1987
- Willis, E.A. McFadden, J.J. “NASA's Rotary Engine Technology Enablement Program -- 1983 through 1991,” SAE No. 920311 NASA Lewis Research Center Group February 1992