This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
1D Model for Correcting the Rate of Injection Signal Based on Geometry and Temperature Influence
Technical Paper
2017-01-0819
ISSN: 0148-7191, e-ISSN: 2688-3627
This content contains downloadable datasets
Annotation ability available
Sector:
Language:
English
Abstract
The fuel consumption and emissions of diesel engines is strongly influenced by the injection rate pattern, which influences the in-cylinder mixing and combustion process. Knowing the exact injection rate is mandatory for an optimal diesel combustion development. The short injection time of no more than some milliseconds prevents a direct flow rate measurement. However, the injection rate is deduced from the pressure change caused by injecting into a fuel reservoir or pipe. In an ideal case, the pressure increase in a fuel pipe correlates with the flow rate. Unfortunately, real measurement devices show measurement inaccuracies and errors, caused by non-ideal geometrical shapes as well as variable fuel temperature and fuel properties along the measurement pipe. To analyze the thermal effect onto the measurement results, an available rate measurement device is extended with a flexible heating system as well as multiple pressure and temperature sensors. With the help of a one-dimensional simulation, the temperature and geometrical effects are further analyzed and available measurement results are confirmed. Afterwards, a correction algorithm is developed which optimizes an assumed injection rate in the simulation model until measured and simulated pressure signals match. A high specialization of the developed algorithm to the optimization task and multiple CPU cores allows a calculation time reduction from multiple hours to minutes in combination with a high flow-rate resolution.
Recommended Content
Citation
Bebber, D. and Reuter, U., "1D Model for Correcting the Rate of Injection Signal Based on Geometry and Temperature Influence," SAE Technical Paper 2017-01-0819, 2017, https://doi.org/10.4271/2017-01-0819.Data Sets - Support Documents
Title | Description | Download |
---|---|---|
Unnamed Dataset 1 |
Also In
References
- Bebber D. van and Reuter U. Analyse und Korrektur des geometrischen und thermischen Einflusses auf Einspritzratenmessungen bei Einsatz eines leitungsbasierten Messsystems 10. Tagung Diesel- und Benzindirekteinspritzung (Helmut Tschöke Springer Vieweg 2016
- Kerékgyártó J. Ermittlung des Einspritzverlaufs an Diesel-Injektoren Ph.D. thesis Institut für Mobile Systeme, Lehrstuhl Kolbenmaschinen (IMS-KM), Universität Magdeburg 2009
- Tremmel O. Technische Beschreibung von Einspritzverlaufsindikator (EVI-IAV) IAV GmbH 2001
- Müller B. Einsatz der Simulation zur Pulsations- und Geräuschminderung hydraulischer Anlagen Ph.D. thesis Institute for Fluid Power Drives and Controls RWTH Aachen, Germany 2002
- Theissen H. Die Berücksichtigung instationärer Rohrströmung bei der Simulation hydraulischer Anlagen Ph.D. thesis Institute for Fluid Power Drives and Controls RWTH Aachen, Germany 1983
- Fluidon GmbH Homepage www.fluidon.com 09 2016
- Hooke R. and Jeeves T. Direct Search Solution of Numerical and Statistical Problems Journal of the ACM 8 2 212 229 1961
- Mathworks Homepage www.mathworks.com 09 2016
- Bosch W. Verfahren zur Ermittlung des zeitlichen Mengenverlaufs von instationär aus einer Düse ausspritzenden, schwach kompressiblen Medien, insbesondere zur Bestimmung des Einspritzgesetzes von Kraftstoffeinspritzanlagen für Brennkraftmaschinen CH Patent 395 644 Stuttgart 1965
- Joukowsky N. 1898 Über den hydraulischen Stoß in Wasserleitungsröhren Mémoires de l'Académie Impériale des Sciences de St.-Pétersbourg, 1900, Series 8 9 5 1 71
- Allievi L. Teoria generale del moto perturbato dell’acqu ani tubi in pressione Atti dell'Associazione Elettrotecnica Italiana 1903 7 2-3 140 196
- Pendovski D. Analysis of the influence of temperature on volumetric flow rates in pipe flows master thesis Institute for Fluid Power Drives and Controls RWTH Aachen, Germany 2015
- Payri R. , Salvador F.J. , Gimeno J. , and Bracho G. A new methodology for correcting the signal cumulative phenomenon on injection rate measurements Experimental Techniques 32 Blackwell Publishing Inc 2008
- Bosch , W. The Fuel Rate Indicator: A New Measuring Instrument For Display of the Characteristics of Individual Injection SAE Technical Paper 660749 1966 10.4271/660749
- Zeuch W. Neue Verfahren zur Messung des Einspritzgesetzes und der Regelmäßigkeit von Diesel Einspritzpumpen MTZ 22, Heft 9 1961
- Bower , G. and Foster , D. A Comparison of the Bosch and Zuech Rate of Injection Meters SAE Technical Paper 910724 1991 10.4271/910724
- Marcic M. Sensor for Injection Rate Measurements Sensors Basel 1367 1382
- Kastengren A. L. ; Tilocco F. Z. , Duke D. J. , Powell C.F. et al. Time-Resolved X-Ray Radiography of Diesel Injectors from the Engine Combustion ICLASS 2012 Heidelberg 2012
- Baum H. and Hofmann M. A New Method for Power Steering Hose Assembly Design and Acoustic Optimisation by means of Time Domain Hydraulic Line Simulation Models PTMC 2007 Bath 2007
- N.N. Unisolierte Feindraht-Thermoelemente Omega GmbH http://www.omega.de/pptst/IRCO_CHAL_P13R_P10R.html 11 2016
- N.N. Piezoelectric Pressure Sensor Kistler Group https://www.kistler.com/?type=669&fid=49891&model=document&callee=frontend 11 2016
- N.N. Shell V-Oil 1404 Shell Deutschland Oil GmbH and Albert Beck GmbH http://schmierstoff-datenbank.de/uploads/tx_albertbeck/1029596834ab094120da31.pdf 11 2016
- Drumm S. M. Entwicklung von Messmethoden hydraulischer Kraftstoffeigenschaften unter Hochdruck Ph.D. thesis Institute for Fluid Power Drives and Controls RWTH Aachen, Germany 2012
- Johnston D. N. Measurement and Prediction of the Fluid-Borne Noise Characteristics of Hydraulic Components and Systems Ph.D. thesis University of Bath 1987
- Kastengren A. L. ; Tilocco F. Z. , Duke D. J. , Powell C.F. , Zhang X. and Moon S. Time-Resolved X-Ray Radiography of Sprays from Engine Combustion Network Spray A Diesel Injectors Atomization and Sprays 24 3 251 272 2014
- Payri , R. , Salvador , F. J. , Gimeno , J. , and Zapata , L. D. Diesel nozzle geometry influence on spray liquid-phase fuel penetration in evaporative conditions Fuel 87 7 1165 1176 2008