This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Effect of Cutting Parameters on Dimensional Hole Quality and Burr Height for One-Shot Drilling of Hybrid Stacks
Technical Paper
2016-01-2101
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
A hybrid drilling process of multi material stacks with one shot drilling recently emerge as an economical and time efficient method in aerospace industry. Even though the comprehensive experience and knowledge is available for the cutting parameters of composites and metals alone, significant gap exist for the hybrid drilling parameters. Determination of these parameters such as feed rate, spindle speed and pecking depth has vital importance so as to provide a robust and optimal process to ensure dimensionally high quality, burr and delamination free holes.
Main challenge of hybrid drilling operation is to obtain required hole diameter with adequate homogeneity and repeatability. In this study, effect of cutting parameters on dimensional hole quality was investigated. In addition to the hole diameter tolerances, CFRP hole enlargement phenomena which is encountered as a specific drawback of metal-exit stack configurations is also addressed within the scope of this study.
Statistical evaluation of hole quality was conducted with calculation of process capability (Cp). Effect of different cutting parameters was compared with respect to these quality variables and optimum parameter set was acquired. In order to demonstrate the effect of cutting parameters on CFRP erosion tendency, number of excessively out of tolerance holes are used and corresponding chip characteristics are evaluated.
This paper presents the results for individual contributions of drilling parameters to the hole quality as well as optimum combination of these parameters specific to given stacking configuration.
This publication summarizes a part of TAI’s research and activities within the context of LOCOMACHS Project funded by EC 7th Framework Program.
Recommended Content
Technical Paper | Future of Sheet Molding Compound (Smc) Body Panels |
Technical Paper | Advancements in Composite Structural Closures |
Technical Paper | Development of Conductible Type Vibration Damping Composite Steel Sheet for Automotive Use |
Authors
Citation
Deger, B., Melemez, F., and Kibar lng, A., "Effect of Cutting Parameters on Dimensional Hole Quality and Burr Height for One-Shot Drilling of Hybrid Stacks," SAE Technical Paper 2016-01-2101, 2016, https://doi.org/10.4271/2016-01-2101.Also In
References
- Liu , D. , Tang , Y. , Cong , W.L. A review of mechanical drilling for composite laminats Composite Structures 94 2012 1265 1279
- Konig W. , Grass P. Quality definition and assessment in drilling of fibre reinforced thermosets Ann. CIRP38/1 1989 119 124
- Shyha I. S. , Aspinwall D. K. , Soo S. L. , Bradley S. Drill geometry and operating effects when cutting small diameter holes in CFRP Int. J. Mach. Tools Manuf 49 2009 1008 1014
- Ramulu M. , Branson T. , Kim D. A study on the drilling of composite and titanium stacks Compos.Struct 54 2001 67 77
- Sharif S. , Rahim E.A. Performance of coated and uncoated carbide tools when drilling titanium alloy Ti-6Al4V J.Mater.Process.Technol 185 2007 72 76
- Pecat O. , Brinksmeier E. Low Damage Drilling of CFRP/Titanium Compound Materials for Fastening 2nd CIRP (CSI). Procedia CIRP 13 2014 1 7
- Kumar M.S. , Prabukarthi A. , Krishnaraj V. Study on Tool Wear and Chip Formation during Drilling Carbon Fiber Reinforced Polymer (CFRP)/ Titanium Alloy (Ti6Al4V) Stacks
- Ramulu M. , Branson T. , Kim D. A study on the drilling of composite and titanium stacks Composite Structures 54 2001 67 77
- Jindal A. Analysis of Tool Wear Rate in Drilling Operation Using Scanning Electron Microscope Journal of Minerals & Materials Characterization & Engineering 2012 11 1 43 54
- Kuo C.L. et al. The effect of cutting speed and feed rate on hole surface integrity in single-shot drilling of metallic-composite stacks Procedia CIRP 13 2014 405 410
- König W. , Wulf C. , Grass P. , Willerscheid H. Machining of Fiber-reinforced plastics Annals of the CIRP 34 1985 537 548
- Shyha I.S. et al. Hole quality assessment following drilling of metallic composite stacks International Journal of Machine Tools & Manufacture 51 2011 569 578
- Wang X. , Kwon P.Y. , Sturtevant C. , Kim D.(Dae-Wook) , Lantrip J. Comparative tool wear study based on drilling experiments on CFRp/ti stack and its individual layers Wear 317 1-2 2014 265 276
- Fernandes M. , Cook C. Drilling of carbon composites using a one shot drill bit. Part I: Five stage representation of drilling and factors affecting maximum force and torque International Journal of Machine Tools & Manufacture 46 2006 70 75