This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Optimization for Brake Feeling in Vehicle without Brake Noise
Technical Paper
2016-01-1928
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Recently, upon customer’s needs for noise-free brake, carmakers are increasingly widely installing damping kits in their braking systems. However, an installation of the damping kits may excessively increase softness in the brake system, by loosening stroke feeling of a brake pedal and increasing compressibility after durability. To find a solution to alleviate this problem, we first conducted experiments to measure compressibility of shims by varying parameters such as adhesive shims (e.g., bonding spec., steel and rubber thickness), piston’s shapes (e.g., different contact areas to the shims), and the numbers of durability. Next, we installed a brake feeling measurement system extended from a brake pedal to caliper. We then compared experimental parameters with brake feeling in a vehicle. Finally, we obtained an optimized level of brake feeling by utilizing the Design for Six Sigma (DFSS). Our results may provide practitioners with a better guideline by helping them design a brake feeling system without brake noise such as squeal.
Recommended Content
Authors
Citation
Jeong, B., Kwak, S., and Kim, C., "Optimization for Brake Feeling in Vehicle without Brake Noise," SAE Technical Paper 2016-01-1928, 2016, https://doi.org/10.4271/2016-01-1928.Also In
References
- Mignery , L. and Nashif , A. Prediction of Damping Treatment Dynamics as Bonded to a Brake Shoe and Lining SAE Technical Paper 1999-01-3407 1999 10.4271/1999-01-3407
- Flint , J. A Review of Theories on Constrained Layer Damping and Some Verification Measurements on Shim Material SAE Technical Paper 2003-01-3321 2003 10.4271/2003-01-3321
- Flint , J. , McDaniel , J. , Li , X. , Elvenkemper , A. et al. Measurement and Simulation of the Complex Shear Modulus of Insulators SAE Technical Paper 2004-01-2799 2004 10.4271/2004-01-2799
- Elvenkemper , A. , Wegmann , E. , Wang , A. , Flint , J. et al. Application of State of the Art FE Software for Simulating the Effect of Insulators SAE Technical Paper 2006-01-3218 2006 10.4271/2006-01-3218
- Dickinson , R. Materials for Noise and Vibration Control: What Causes Product Variability? SAE Technical Paper 2006-01-3226 2006 10.4271/2006-01-3226
- Hoffrichter , W. , Schmitt , O. , and Fecske , L. Development of Shim Specifications SAE Technical Paper 2008-01-2545 2008 10.4271/2008-01-2545
- Dickinson , R. Vehicle Brake Noise Shims: A Tutorial for Continuous Product Improvements SAE Technical Paper 2008-01-2547 2008 10.4271/2008-01-2547
- Ahmed , I. , Metwally , S. , Mohamed , E. , and Abouel-Seoud , S. Influence of Surface Modifications on Vehicle Disc Brake Squeal SAE Technical Paper 2009-01-1977 2009 10.4271/2009-01-1977
- Day , A. , Ho , H. , Hussain , K. , and Johnstone , A. Brake System Simulation to Predict Brake Pedal Feel in a Passenger Car SAE Technical Paper 2009-01-3043 2009 10.4271/2009-01-3043
- Jun , H. , Xue-xun , G. , and Gang-feng , T. Complex Mode Analysis on Disc Brake Squeal and Design Improvement SAE Technical Paper 2009-01-2101 2009 10.4271/2009-01-2101
- Denys , E. and Thompson , J. The Development of a Brake Insulator Damping Measurement Procedure SAE Technical Paper 2010-01-1685 2010 10.4271/2010-01-1685
- Backstrom , A. An Experimental Investigation of Brake Rotor DTV Under Laboratory Conditions - Part 3 SAE Technical Paper 2010-01-1690 2010 10.4271/2010-01-1690
- Backstrom , A. Brake Drag Fundamentals SAE Technical Paper 2011-01-2377 2011 10.4271/2011-01-2377
- Flint , J. , Chinnasamy , A. , and Stikvoort , A. New Method to Identify Dynamic Normal Stiffness and Damping of Shims for CAE Modeling SAE Technical Paper 2010-01-1711 2010 10.4271/2010-01-1711
- Antanaitis , D. , Riefe , M. , and Sanford , J. Automotive Brake Hose Fluid Consumption Characteristics and Its Effects on Brake System Pedal Feel SAE Int. J. Passeng. Cars - Mech. Syst. 3 1 113 130 2010 10.4271/2010-01-0082
- Fulco , E. , Tonet , G. , Matozo , L. , and Varante , P. Influence of the Shim Contact Stiffness on Disc Brakes Squeal Noise SAE Technical Paper 2013-36-0014 2013 10.4271/2013-36-0014
- Koizumi , N. Effect of Phenolic Brake Piston Tribology on Brake Pedal Feel SAE Int. J. Mater. Manf. 7 1 1 9 2014 10.4271/2013-01-2051
- Schomaker , R. , Pedwell , R. , and Knickrehm , B. Methodology for Classification of Shim Materials SAE Int. J. Aerosp. 7 2 255 262 2014 10.4271/2014-01-2253
- Shimizu , H. , Oura , Y. , Suzuki , T. , and Sano , Y. The Effect of Grease on Brake Squeal SAE Technical Paper 2014-01-2512 2014 10.4271/2014-01-2512
- Antanaitis , D. , Ciechoski , C. , and Riefe , M. Further Research into the Role of the Caliper Piston in Brake Roughness SAE Int. J. Commer. Veh. 8 2 258 270 2015 10.4271/2015-01-2667