This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Experiments on the Effect of Pressure and Voltage Supply on Pulse Injector Opening Time
Technical Paper
2014-01-2560
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The paper presents the results of experiments on the effects of supply pressure and supply voltage on the pulse gas injector opening time. Two characteristics have been investigated into: the opening lag time and the time of opening. The injector's opening lag was defined as the time between the occurrence of a control signal and the moment of the valve's starting to move. The injector's time of opening was defined as the time of the valve element's movement from the closed to the fully open position.
The analysis covered 6 injector types differing in the design of the valve element and the coil. The injectors types were representative of designs most popular in the market: piston and plate injectors calibrated by means of the piston stroke or the outlet diameter. The experiments were conducted in a bespoke test bed, and compressed air was used in lieu of gas fuel. The paper presents the test bed and discusses the method of determining the moment of the valve element's starting to move and stopping.
In general, the results indicate that a linear increase in pressure increases the injector opening lag, but has practically no effect on the time of opening. Moreover, increasing the supply voltage reduces both the injector opening lag time and the time of opening. The tests pointed to considerable differences between injector types with respect to the scale of reaction to supply voltage and pressure levels. The results were used to construct a model of opening lag time and time of opening in the function of supply pressure and supply voltage.
Citation
Czarnigowski, J., "Experiments on the Effect of Pressure and Voltage Supply on Pulse Injector Opening Time," SAE Technical Paper 2014-01-2560, 2014, https://doi.org/10.4271/2014-01-2560.Also In
References
- Bleischwitz R. , Bader N. Policies for the transportation toward a hydrogen economy: The EU case Energy Policy 38 2010 5388 5398
- Litschke A. , Knitschky G. Future development in road freight transport re-garding more environmentally friendly vehicle technology Procedia - Social and Behavioral Sciences 48 2012 1557 1567
- Kenihan S. Reducing the emissions from your council fleet Cities for Climate Protection Australia: An ICLEI program in collaboration with the AGO http://www.iclei.org 1999
- Czarnigowski J. Teoretyczno-empiryczne studium modelowania impulsowego wtryskiwacza gazu Monografie Politechnika Lubelska Lublin 2012
- Van Basshuysen , R. and Schaefer , F. Internal Combustion Engine Handbook Society of Automotive Engineers, Inc. Warrendale, PA 978-0-7680-1139-5 2004 10.4271/R-345
- Van Basshuysen , R. and Schaefer , F. Modern Engine Technology from A to Z SAE International Warrendale, PA 978-0-7680-1705-2 2007 10.4271/R-373
- Czarnigowski J. , Barański G. , Wendeker M. , Duk M. , Zyska T. Method to measure injector opening and closing lag times PTNSS-2011-SS1-103 COMBUSTION ENGINES, No. 1/2011 (144)
- Czarnigowski J. The impact of a material used in a gas injector magnetic core on gas injector performance PTNSS-2011-SC-017 COMBUSTION ENGINES, No. 1/2011 (144)
- Grabowski Ł. , Wendeker M. , Pietrykowski K. , Jakliński P. , Czarnigowski J. , Sochaczewski R. The Simulation Research of the Induction Process of a Four-Cylinder Spark Ignitron Engine Fuelled by LPG Sequential Injection PTNSS-2009-SC-052 Combustion Engines Silniki Spalinowe Special Series 2009-SC2 136 144
- Jakliński , P. , Czarnigowski , J. , and Wendeker , M. The Effect of Injection Start Angle of Vaporized LPG on SI Engine Operation Parameters SAE Technical Paper 2007-01-2054 2007 10.4271/2007-01-2054
- Wendeker , M. , Jakliński , P. , Czarnigowski , J. , Boulet , P. et al. Operational Parameters of LPG Fueled SI Engine - Comparison of Simultaneous and Sequential Port Injection SAE Technical Paper 2007-01-2051 2007 10.4271/2007-01-2051
- Elbaum J. Obwody magnetyczne Państwowe Wydawnictwa Techniczne Warszawa 1959
- Czarnigowski J. , Jakliński P. , Wendeker M. , Barański G. , Pietrykowski K. , Duk M. The influence of Input Pressure on Gas Injector Opening and Closing Lag Time PTNSS-2009-SC-054 Combustion Engines Silniki Spalinowe Special Series 2009-SC1 str. 103-108