This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Increase in Vehicle Front, Rear and Side Stiffness Coefficients in the Past Twenty Years Necessitates New Representative Database
Technical Paper
2014-01-0351
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
When vehicle-specific stiffness coefficients cannot be acquired, stiffness coefficient values that are representative of the desired vehicle type, class, wheelbase or weight are routinely used for accident reconstructions. Since the original compilation of representative vehicle stiffness data almost 20 years ago, changes in crash testing standards and other safety and technological improvements in vehicular design have affected vehicle stiffness. While generic frontal stiffness data have been recently updated to reflect these vehicular changes, rear and side stiffness data have not. Structural, geometric and inertial data for over 300 passenger cars and light trucks were collected. Among the vehicles targeted were the top-selling cars, SUVs, vans and pickups for model years 1990 to 2012. Results indicated that all vehicle types demonstrated increases in mean stiffness over the time period considered. SUVs were, on average, the stiffest vehicle type in the front, rear and side. There was a correlation between vehicle wheelbase and stiffness, with longer vehicles having greater stiffness than shorter vehicles. Vehicle class also affected stiffness. In the front and rear, mid-size passenger cars had the greatest mean “A” and “B” stiffness coefficients of all passenger cars. By contrast to the front and rear, mean side stiffness of all passenger cars classes was similar. In conclusion, the updated structural stiffness and geometric data presented here for the front, rear and side, provide an accurate representation of today's market for use in crash reconstructions.
Recommended Content
Authors
Citation
Lee, E., Lee, P., Erickson, M., and Hayes, W., "Increase in Vehicle Front, Rear and Side Stiffness Coefficients in the Past Twenty Years Necessitates New Representative Database," SAE Technical Paper 2014-01-0351, 2014, https://doi.org/10.4271/2014-01-0351.Also In
References
- Campbell , K. Energy Basis for Collision Severity SAE Technical Paper 740565 1974 10.4271/740565
- Day , T. and Hargens , R. An Overview of the Way EDCRASH Computes Delta-V SAE Technical Paper 870045 1987 10.4271/870045
- Prasad , A. CRASH3 Damage Algorithm Reformulation for Front and Rear Collisions SAE Technical Paper 900098 1990 10.4271/900098
- Struble , D. Generalizing CRASH3 for Reconstructing Specific Accidents SAE Technical Paper 870041 1987 10.4271/870041
- Smith , R. and Noga , J. Accuracy and Sensitivity of CRASH SAE Technical Paper 821169 1982 10.4271/821169
- Siddall , D. and Day , T. Updating the Vehicle Class Categories SAE Technical Paper 960897 1996 10.4271/960897
- National Highway Traffic Safety Administration (NHTSA) Corporate Average Fuel Economy http://www.nhtsa.gov/fuel-economy 2013
- Samaha , R. , Digges , K. , Fesich , T. , and Authaler , M. Frontal Crash Testing and Vehicle Safety Designs: A Historical Perspective Based on Crash Test Studies SAE Technical Paper 2010-01-1024 2010 10.4271/2010-01-1024
- Osterholt , G. , Cummings , J. , Biller , B. , and Calhoun , V. Updating Generic Crush Stiffness Coefficients for Accident Reconstruction SAE Technical Paper 2010-01-1581 2010 10.4271/2010-01-1581
- WardsAuto Ward's Motor Vehicle Facts and Figures http://wardsauto.com/data-center 1990 2012
- U.S.Department of Energy Fuel economy guide DOE/EE-0603 2013
- Swanson J , Rockwell T , Beuse N et al. Evaluation of stiffness measures from the U.S. new car assessment program Proceedings of Inter-Noise Paper No. 527 2003