This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Effects of Injection Pressure, Timing and EGR on Combustion and Emissions Characteristics of Diesel PCCI Engine
Technical Paper
2011-01-1769
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Effects of injection parameters on combustion and emission characteristics of diesel PCCI engine operating on optical and test engine was investigated. PCCI combustion was achieved through slightly narrow included angle injector, low compression ratio coupled with exhaust gas recirculation. Analysis based on diesel spray evolution, combustion process visualization and analysis was carried out. Spray penetration was evaluated and related to the exhaust emissions. Advancing the injection timing and EGR extended the ignition delay, decreased NOx emissions and increased HC, smoke and CO emissions. Higher injection pressure led to low emissions of NOx, smoke, HC and comparable CO. Optimum spray targeting position for minimum emission was identified. Impingement on the piston surface led to deterioration of emissions and increased fuel consumption while spray targeting the upper edge of Derby hat wall showed improvement in emission and engine performance.
Recommended Content
Authors
Topic
Citation
Kiplimo, R., Tomita, E., Kawahara, N., Zhou, S. et al., "Effects of Injection Pressure, Timing and EGR on Combustion and Emissions Characteristics of Diesel PCCI Engine," SAE Technical Paper 2011-01-1769, 2011, https://doi.org/10.4271/2011-01-1769.Also In
References
- Akihama, K. Takatori, Y. Inagaki, K. Sasaki, S. Dean, A.M. “Mechanism of Smokeless Rich Diesel Combustion by Reduced Temperature,” SAE Technical Paper 2001-01-0665 2001
- Jacobs, T. J. Assanis, D. “The Attainment of Premixed Compression Ignition Low-Temperature Combustion in a Compression Ignition Direct Injection Engine Proceedings of the Combustion Institute 31 2913 2920 2007
- Boot, D.M. Luijten, M.C.C. Somers, T.M. L. Eguz, U. van Erp, M.T.D.D. Albrecht, A. Baert, G.S.R. “Uncooled EGR as a Means of Limiting Wall Wetting Under Early Direct Injection Conditions,” SAE Technical paper 2009-01-0665 2009
- Ladommatos, N. Abdelhamin, S. Zhao, H. “Control of Oxides of Nitrogen from Diesel Engine Using Diluents While Maintaining the Impact on Particulate Pollutant,” Applied Thermal Engineering 1998 18 963 980
- Mallamo, F. Badami, M. Millo, F. “Effect of Compression Ratio and Injection Pressure on Emissions and Fuel Consumption of a Small Displacement Common Rail Diesel Engine,” SAE Technical Paper 2005-01-0379 2005
- de Ojeda, W. Kumar, R. Zoldak, P. Espinosa, R. “Development of a Fuel Injection Strategy for Diesel LTC,” SAE Technical Paper no. 2008-01-0057 2008
- Martin, G. Mueller, C. Milam, D. Radovanovic, M. et al. “Early Direct-Injection, Low-Temperature Combustion of Diesel Fuel in an Optical Engine Utilizing a 15-Hole, Dual-Row, Narrow-Included-Angle Nozzle,” SAE Int. J. Engines 1 1 1057 1082 2009 10.4271/2008-01-2400
- Lee, S. Reitz, R.D. “Spray Targeting to Minimize Soot and CO Formation in Premixed Charge Compression Ignition (PCCI) Combustion with a HSDI Diesel Engine,” SAE Technical Paper 2006-01-0918 2006
- Genzale, C. Reitz, R. Musculus, M. “Effects of Piston Bowl Geometry on Mixture Development and Late-Injection Low-Temperature Combustion in a Heavy-Duty Diesel Engine,” SAE Int. J. Engines 1 1 913 937 2009 10.4271/2008-01-1330
- Boot, M. Rijk, E. Luijten, C. Somers, B. Albrecht, B. “Spray Impingement in the Early Direct Injection Premixed Charge Compression Ignition Regime,” SAE International 2010-01-1501 2010
- Kimura, S. Aoki, O. Ogawa, H. Marunaka, S. Enomoto, Y. “New Combustion Concept for Ultra-Clean and High-Efficiency Small DI Diesel Engine SAE 1999-01-3681 1999
- Takeda, Y. Keiichi, N. Niimura, Keiichi “Emission Characteristics of Premixed Lean Diesel Combustion with Extremely Early Staged Fuel Injection” SAE 961163 1996
- Kook, S. Park, S. Bae, C. “Influence of Early Injection Timings on Premixing and Combustion in a Diesel Engine” Energy & Fuels 2008 22 331 337
- Kook, S. Bae, C. Kim, J. “Diesel-Fuelled Homogenous Charge Compression Ignition Engine with Optimized Premixing Strategies” Int. J. Engine Res. 8 2007
- Dodge, L.G. Simescu, S. Neely, D.G. Maymar, J.M. Dickey, W.D. Savonen, L.C. “Effect of Small Holes and High Injection Pressure on Diesel Engine Combustion,” SAE Technical paper 2002-01-0494 2002
- Henein, N. A. Bhattacharyya, B. Schipper, J. Kastury, A. Bryzik, W. “Effect of Injection Pressure and Swirl Motion on Diesel -out Emissions in Conventional and Advanced Combustion Regimes,” SAE Paper 2006-01-0076 2006
- Lee, H.K. Lee, H. C. “An experimental Study on the Combustion and Emission Characteristics of a Stratified Charge Compression Ignition (SCCI) Engine,” Energy & Fuels 2007 21 1901 1907
- Roy, M. M. Tomita, E. Kawahara, N. Harada, Y. Sakane, A. “An Experimental Investigation on Engine Performance and Emission of A Supercharged H 2 Diesel Dual Fuel Engine,” Int. Journal of Hydrogen Energy 35 844 853 2010
- Shao, J. Yan, Y. “Digital Imaging Based on Measurement of Diesel Spray Characteristics,” IEEE Transactions on Instrumentation and Measurement 57 9 2008
- Aoyagi, Y. Osada, H. Misawa, M. Goto, Y. Ishii, H. “Advanced Diesel Combustion Using of Wide Rang, High Boosted and Cooled EGR System by Single Cylinder Engine,” SAE paper 2006-01-0077 2006
- Kook, S. Bae, C. Miles, P.C. Choi, D. Pickett, L.M. “The Influence of Charge Dilution and Injection Timing on Low- Temperature Diesel Combustion and Emissions,” SAE Technical Paper 2005-01-3837 2005
- Heywood, J.B. “Internal Combustion Engine Fundamentals” McGraw Hill, Inc. 1988