This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Fast, High Resolution Panel Noise Contribution Method
Technical Paper
2011-01-1594
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
All surfaces of a cabin interior may contribute to the sound pressure at a certain reference position, e.g. the human's ear. Panel noise contribution analysis (PNCA) involves the measurement of the contribution of separate areas. This is an effective method to determine the effect of apparent noise sources at a specific location.
This paper presents the latest developments on particle velocity based panel noise contribution analysis. In contrast to the traditional methods, the particle velocity approach is faster; it requires 3 days instead of weeks. While the theoretical base of the procedure in this paper is similar to previously published particle velocity based procedure, here the measurement protocol has now been simplified dramatically, which has reduced the measurement time even more to less than a day. The method and its implementation are explained in the paper and a full measurement procedure is reported.
Four steps are required to determine and visualize the pressure contribution of the vehicle interior.
In a first step, probes are positioned on predefined interior surfaces. Special probe mounting have been made to decrease the handling time.
The second step is a measurement in a certain mode of operation. This step can be done in a laboratory but it is also possible to perform the measurement whilst driving the vehicle on the road. Stationary as well as non stationary running conditions like run ups are accessible and do not limit the applicability of the method.
The third step is the determination of the transfer paths from the panels to a certain listening position. This measurement is done assuming reciprocity. A monopole source is placed on the listener position and the sound pressure is measured at the surface.
In a fourth and last step the transfer paths are linked with the operational data gathered in step two. The results are then visualized using the predefined geometry model.
This paper describes the measurement of a conventional car with a resolution of 137 panels. Since an array of 46 probes was used step 2 and step 3 are repeated 3 times.
Recommended Content
Authors
Citation
Tijs, E., Wind, J., and Fernández Comesaña, D., "Fast, High Resolution Panel Noise Contribution Method," SAE Technical Paper 2011-01-1594, 2011, https://doi.org/10.4271/2011-01-1594.Also In
References
- Fahy, F.J. Some Applications of the Reciprocity Principle in Experimental Vibroacoustics Acoustical Physics 49 2 217 229 2003
- Wolff, O. Sottek, R. “Panel Contribution Analysis - An Alternative Window Method,” SAE Technical Paper 2005-01-2274 2005 10.4271/2005-01-2274
- Hald, J. Tsuchiya, Masaki Panel Contribution Analysis using a Volume Velocity Source and a Double Layer Array with the SONAH Algorithm the proceedings of INTER-NOISE 2006
- Hald, J. STSF - a unique technique for schan-based Near-field Acoustic Holography without restrictions on hoherence Brüel & Kjær, Technical Review 1
- Kinsler, L.E. Frey, A.R. Coppens, A.B. Sanders, J.V. Fundamentals of Acoustics 4th Wiley and Sons 2000
- Wolff, O. Fast panel noise contribution analysis using large PU sensor arrays Internoise 2007
- de Bree, H. Basten, T. “Microflown Based Monopole Sound Sources for Reciprocal Measurements,” SAE Technical Paper 2008-36-0503 2008 10.4271/2008-36-0503
- Rondeau, J. Duval, A. Deshayes, G. Lassalas, M. et al. “Vehicle Acoustic Synthesis Method: Improving Acquisition Time by Using P-U Probes,” SAE Technical Paper 2005-01-2444 2005 10.4271/2005-01-2444
- Duval, A. Rondeau, J. Bischoff, L. Morgenstern, C. et al. “Vehicle Acoustic Synthesis Method 2nd Generation: New Developments with p-u Probes Allowing to Simulate Unsteady Operative Conditions Like Run-Ups,” SAE Technical Paper 2007-01-2271 2007 10.4271/2007-01-2271
- Jacobsen, F. de Bree, H.E A Comparison of two different sound intensity measurement principles JASA 2005
- Fernández Comesaña, D. Wind, J. de Bree, H. “A Scanning Method for Source Visualization and Transfer Path Analysis Using a Single Probe,” SAE Technical Paper 2011-01-1664 2011 10.4271/2011-01-1664