This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Mean Value Engine Modeling for a Diesel Engine with GT-Power 1D Detail Model
Technical Paper
2011-01-1294
ISSN: 0148-7191, e-ISSN: 2688-3627
This content contains downloadable datasets
Annotation ability available
Sector:
Language:
English
Abstract
Mean value engine model (MVEM) is the basis of control design for advanced internal combustion engines. The engine performance transient process usually takes a few cycles. The MVEM provides an adequate accurate description of the engine dynamics with reasonable approximation by ignoring the heat loss and sub-cycle events. MVEM is very important for engine system control development, especially when the modern engine becomes more and more complicated when equipped with throttle, turbocharger and after-treatment systems. Usually the MVEM is developed based on data from engine tests, which is a costly and time consuming process. In this paper, the air path MVEM modeling method based on the 1D detail model is discussed for a turbocharged diesel engine. Simulation is applied to demonstrate the effectiveness of this new method. This approach could be used to get the MVEM for control design even before the prototype engine is available. It reduces the cost, risk and labor compared with the test data based approach. This MVEM model can be built in modules and the parameters can be validated for a specific engine. These advantages make it applicable to a wide range of engines.
Recommended Content
Journal Article | Development of a Quasi-Dimensional Combustion Model for Stratified SI-Engines |
Technical Paper | On a Model-Based Control of a Three-Way Catalytic Converter |
Technical Paper | A Simple Physical Model of ICE Mechanical Losses |
Authors
Citation
Wu, H., Wang, X., Winsor, R., and Baumgard, K., "Mean Value Engine Modeling for a Diesel Engine with GT-Power 1D Detail Model," SAE Technical Paper 2011-01-1294, 2011, https://doi.org/10.4271/2011-01-1294.Data Sets - Support Documents
Title | Description | Download |
---|---|---|
Unnamed Dataset 1 | ||
Unnamed Dataset 2 |
Also In
References
- Bengtsson, J. Strandh, P. Johansson, R. Tunestal, P. Johansson, B. “Hybrid Modelling of Homogeneous Charge Compression Ignition (HCCI) Engine Dynamics - a Survey,” International Journal of Control 80 1814 1847 2007
- Canova, M. Chiara, F. Flory, M. Midlam-Mohler, S. Guezennec, Y. Rizzoni, G. “Dynamics and control of DI and HCCI combustion in a multi-cylinder diesel engine,” Fifth IFAC Symposium on Advances in Automotive Control 2007 Seascape Resort California, USA 2007
- Chauvin, J. Corde, G. Petit, N. Rouchon, P. “Airpath Strategy for Experimental Transient Control of a Diesel HCCI Engine,” Oil & Gas Science and Technology - Rev. IFP 62 483 491 2007
- Pettiti, M. Pilo, L. Millo, F. “Development of a New Mean Value Model for the Analysis of Turbolag Phenomena in Automotive Diesel Engines,” SAE Technical Paper 2007-01-1301 2007 10.4271/2007-01-1301
- Los Alamos National Laboratory “KIVA-II: A Computer Program for Chemically Reactive Flows with Sprays,” 1989
- He, Y. Lin, C.-C. “Development and Validation of a Mean Value Engine Model for Integrated Engine and Control System Simulation,” SAE Technical Paper 2007-01-1304 2007 10.4271/2007-01-1304
- Schulten, P. J. M. Stapersoma, D. “Mean Value Modelling of the Gas Exchange of a 4-stroke Diesel Engine for Use in Powertrain Applications,” SAE Technical Paper 2003-01-0219 2003 10.4271/2003-01-0219
- He, Y. “Development And Validation of A 1D Model of A Turbocharged V6 Diesel Engine Under Steady State and Transient Conditions,” SAE Technical Paper 2005-01-3857 2005 10.4271/2005-01-3857
- Wu, H. Wang, X. Winsor, R. Baumgard, K. “Integrated Simulation of Engine Performance and AFR Control of a Stoichiometric Compression Ignition (SCI) Engine,” SAE Technical Paper 2011-01-0698 2011 10.4271/2011-01-0698
- Heywood, J. B. “Internal Combustion Engines Fundamentals,” McGraw-Hill Book Company New York 0-07-100499-8 255 260 1988
- Hendricks, E. Chevaller, A. Jensen, M. Sorenson, S. C. Trumpy, D. Asik, J. “Modeling of the Intake Manifold Filling Dynamics,” SAE Technical Paper 960037 1996 10.4271/960037