This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Modeling of Engine and Vehicle for a Compact Car with a Flywheel Based Kinetic Energy Recovery Systems and a High Efficiency Small Diesel Engine
Technical Paper
2010-01-2184
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Recovery of kinetic energy during driving cycles is the most effective option to improve fuel economy and reduce green house gas (GHG) emissions. Flywheel kinetic energy recovery systems (KERS) may boost this efficiency up to values of about 70%. An engine and vehicle model is developed to simulate the fuel economy of a compact car equipped with a TDI diesel engine and a KERS. Introduction of KERS reduces the fuel used by the 1.6L TDI engine to 3.16 liters per 100 km, corresponding to 82.4 g of CO₂ per km. Downsizing the engine to 1.2 liters as permitted by the torque assistance by KERS, further reduces the fuel consumption to 3.04 liters per 100 km, corresponding to 79.2 g of CO₂ per km. These CO₂ values are 11% better than those of today's most fuel efficient hybrid electric vehicle.
Recommended Content
Authors
Topic
Citation
Boretti, A., "Modeling of Engine and Vehicle for a Compact Car with a Flywheel Based Kinetic Energy Recovery Systems and a High Efficiency Small Diesel Engine," SAE Technical Paper 2010-01-2184, 2010, https://doi.org/10.4271/2010-01-2184.Also In
References
- http://www.vcacarfueldata.org.uk 8 1 10
- http://www.flybridsystems.com/Technology.html 8 1 10
- http://www.torotrak.com/IVT/works/ 8 1 10
- http://www.xtrac.com/pdfs/Torotrak_Xtrac_CVT.pdf 8 1 10
- http://www.bhr-technology.com/CPC-KERS.pps 8 1 10
- Stone, R. “Full-toroidal variable drive transmission systems in mechanical hybrid systems - from Formula 1 to road cars” CTI Symposium and Exhibition: Automotive Transmissions Berlin, Germany December 2009 http://www.torotrak.com/Resources/Torotrak/Documents/Mech%20hybrid%20paper_CTI%20Berlin09.pdf January 11 2010
- Body, W. Brockbank, C. “Simulation of the fuel consumption benefits of various transmission arrangements and control strategies within a flywheel based mechanical hybrid system” VDI Transmissions in Vehicles Conference and Exhibition Friedrichshafen June 2009 http://www.torotrak.com/Resources/Torotrak/Documents/VDI%20Friedrichshafen%202009.pdf January 11 2010
- Brockbank, C. Greenwood, C. “Full-toroidal variable drive transmission systems in mechanical hybrid systems - from Formula 1 to road vehicles” CTI Symposium and Exhibition: Automotive Transmissions Detroit May 2009 http://www.torotrak.com/Resources/Torotrak/Documents/CTI%20Detroit%20Paper%202009.pdf January 11 2010
- Brockbank, C. “Application of a Variable Drive to Supercharger & Turbo Compounder Applications,” SAE Technical Paper 2009-01-1465 2009 10.4271/2009-01-1465
- Cross, D. Brockbank, C. “Mechanical Hybrid System Comprising a Flywheel and CVT for Motorsport and Mainstream Automotive Applications,” SAE Technical Paper 2009-01-1312 2009 10.4271/2009-01-1312
- Brockbank, C. Greenwood, C. “Full-toroidal variable drive transmission systems in mechanical hybrids - from Formula 1 to road vehicles” CTI Innovative Automotive Transmissions Conference and Exhibition Berlin December 2008 http://www.torotrak.com/Resources/Torotrak/CTI_Berlin_2008.pdf January 11 2010
- Brockbank, C. Greenwood, C. “Formula 1 mechanical hybrid applied to mainstream automotive” VDI Getriebe in Fahrzeuge Conference June 2008 http://www.torotrak.com/Resources/Torotrak/VDI_2008.pdf January 11 2010
- http://www.ricardo.com/Documents/PRs%20pdf/PRs%202009/Ricardo%20Kinergy%20delivers%20breakthrough%20technology%20low%20cost%20hybridisation.pdf 11 01 10
- http://www.ricardo.com/engb/Software/Productoffering-description/WAVE1/ 8 1 10
- http://www.lesoft.co.uk/index1.html 20 1 10
- Diego-Ayala, U. Martinez-Gonzalez, P. McGlashan, N. Pullen, K. “The mechanical hybrid vehicle: an investigation of a flywheel-based vehicular regenerative energy capture system” Proc. IMechE Vol. 222 Part D: J. Automobile Engineering 2087 2101 2008 10.1243/09544070JAUTO677
- Kasama, R. Naito, S. Katada, H. Shibata, T. “The Efficiency Improvement of Electric Vehicles by Regenerative Braking,” SAE Technical Paper 780291 1978 10.4271/780291
- Slutsky, S. Levi, E. “Regenerative Braking in Diesel-Powered Urban Buses,” SAE Technical Paper 841690 1984 10.4271/841690
- Wyczalek, F.A. Wang, T.C. “Regenerative Braking Concepts for Electric Vehicles - A Primer,” SAE Technical Paper 920648 1992 10.4271/920648
- Wyczalek, F.A. Wang, T.C. “Electric Vehicle Regenerative Braking,” SAE Technical Paper 929139 1992 10.4271/929139
- von Albrichsfeld, C. Karner, J. “Brake System for Hybrid and Electric Vehicles,” SAE Technical Paper 2009-01-1217 2009 10.4271/2009-01-1217
- Sovran, G. Blaser, D. “Quantifying the Potential Impacts of Regenerative Braking on a Vehicle's Tractive-Fuel Consumption for the U.S., European, and Japanese Driving Schedules,” SAE Technical Paper 2006-01-0664 2006 10.4271/2006-01-0664
- Panagiotidis, M. Delagrammatikas, G. Assanis, D. “Development and Use of a Regenerative Braking Model for a Parallel Hybrid Electric Vehicle,” SAE Technical Paper 2000-01-0995 2000 10.4271/2000-01-0995
- Wittmer, C. Dietrich, P. Guzzella, L. “Control Strategies for the ETH-Hybrid III Vehicle” 1995 Proceedings First IFAC Workshop on Advances in Automotive Control
- Wittmer, C. Guzzella, L. Dietrich, P. “Optimized Control Strategies for a Hybrid Car with a Heavy Flywheel” 1996 Automatisierungstechnik 7 331 337
- Guzzella, L. Wittmer, Ch. Ender, M. “Optimal Operation of Drive trains with SI-Engines and Fly-Wheels” 1996 Proceedings of the 13th IFAC World Congress
- Vroemen, B. Serrarens, A. Veldpaus, F. “Hierarchical control of the Zero Inertia power train” JSAE 22 4 2001 http://www.mate.tue.nl/mate/pdfs/1511.pdf June 24 2010
- http://www.transportation.anl.gov/facilities/vehicle_datasheets.html July 20 2010
- http://spaceresearch.nasa.gov/general_info/flywheel.html July 20 2010
- Boretti, A. “Improvements of vehicle fuel economy using mechanical regenerative braking” 3 7 2010 International Journal of Vehicle Design