This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Updating Generic Crush Stiffness Coefficients for Accident Reconstruction
Technical Paper
2010-01-1581
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Often, the accident reconstructionist will find that there is no crash test data for a particular vehicle, making a direct calculation of the crush stiffness coefficients impossible without performing an actual crash test. A faster and more cost effective solution is to use “generic” crush stiffness coefficients that relate similar already tested vehicles to the incident vehicle. One previously published article that has been used for this purpose is; “Updating the Vehicle Class Categories” by Siddall and Day [
9
]. However, this paper, along with Hargens and Day's earlier paper, “Vehicle Data Sources for Accident Reconstruction” [
3
], are now somewhat outdated by newer model vehicles.
New generic crush stiffness coefficient values were calculated to better represent newer vehicles produced between 1990-1999 and 2000-2009. The same eleven vehicle classifications used in this article were obtained from the above cited paper.
The crush stiffness coefficients were calculated for each category for the entire population of the data used. The data was broken into different decades in which the vehicles were produced. After the analysis was performed, it was noted that crush stiffness values showed an upward trend for newer vehicles.
Recommended Content
Authors
Citation
Osterholt, G., Cummings, J., Biller, B., and Calhoun, V., "Updating Generic Crush Stiffness Coefficients for Accident Reconstruction," SAE Technical Paper 2010-01-1581, 2010, https://doi.org/10.4271/2010-01-1581.Also In
References
- Chen, H.F. Tanner, C.B. Cheng, P.H. Guenther, D.A. “Application of Force Balance Method in Accident Reconstruction,” SAE Technical Paper 2005-01-1188 2005 10.4271/2005-01 -1188
- Digges, K. Eigen, A. Bahouth, G. “Stiffness and Geometric Compatibility in Front-to-Side Crashes,” SAE Technical Paper 2002-01-1020 2002 10.4271/2002-01-1020
- Hargens, R.L. Day, T.D. “Vehicle Data Sources for Accident Reconstruction,” SAE Technical Paper 880070 1988 10.4271/880070
- Hull, W.C. Newton, B.E. “Estimating Crush Stiffness when Reconstructing Vehicle Accidents,” SAE Technical Paper 930898 1993 10.4271/930898
- Neptune, J.A. Blair, G.Y. Flynn, J.E. “A Method for Quantifying Vehicle Crush Stiffness Coefficients,” SAE Technical Paper 920607 10.4271/920607
- Neptune, J.A. Flynn, J.E. “A Method for Determining Accident Specific Crush Stiffness Coefficients,” SAE Technical Paper 940913 10.4271/940913
- Neptune, J.A. Flynn, J.E. “A Method for Determining Crush Stiffness Coefficients from Offset Frontal and Side Crash Tests,” SAE Technical Paper 980024 1998 10.4271/980024
- NHTSA 2009 “Database Exports.” February 23 2009 http://www-nrd.nhtsa.dot.gov/database/aspx/download.aspx?tst no=&curno=&database=v&name=Vehdb-export&format=export
- Siddall, D.E. Day, T.D. “Updating the Vehicle Class Categories,” SAE Technical Paper 960897 1996 10.4271/960897
- Strother, C.E. Kent, R.W. Warner, C.Y. “Estimating Vehicle Deformation Energy for Vehicles Struck in the Side,” SAE Technical Paper 980215 1998 10.4271/980215
- Traffic Accident Reconstruction Fricke, Lynn B. Northwestern University
- Traffic Collision Investigations Baker, Kenneth S. Northwestern University