This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Study of a Heavy Duty Euro5 EGR-Engine Sensitivity to Fuel Change with Emphasis on Combustion and Emission Formation
Technical Paper
2010-01-0872
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
A diesel engine developed for an international market must be able to run on different fuels considering the diesel fuel qualities and the increasing selection of biofuels in the world. This leads to the question of how different fuels perform relative to a standard diesel fuel when not changing the hardware settings.
In this study five fuels (Japanese diesel, MK3, EN590 with 10% RME, EN590 with 30% RME and pure RME) have been compared to a reference diesel fuel (Swedish MK1) when run on three different speeds and three different loads at each speed. The experiments are run on a Scania 13l Euro5 engine with standard settings for Swedish MK1 diesel.
In general the differences were not large between the fuels. NO
x
usually increased compared to MK1 and then soot decreased as would be expected. The combustion efficiency increased with increased RME contents of the fuel but the indicated efficiency was not influenced by RME except for at higher loads. The pressure rise rates were increased compared to MK1, in most cases, for all fuels and especially for the Japanese fuel.
Recommended Content
Authors
Topic
Citation
Zander, C., Stenlaas, O., Tunestal, P., and Johansson, B., "Study of a Heavy Duty Euro5 EGR-Engine Sensitivity to Fuel Change with Emphasis on Combustion and Emission Formation," SAE Technical Paper 2010-01-0872, 2010, https://doi.org/10.4271/2010-01-0872.Also In
References
- Cipolat, D. “The Effect of Fuel Characteristics on the Fuel Injection Process in a CI Engine Fuelled on Diesel and DME,” SAE Technical Paper 2007-24-0119 2007
- Ireland, J. McCormick, R. Yanowitz, J. Wright, S. “Improving Biodiesel Emissions and Fuel Efficiency with Fuel-Specific Engine Calibration,” SAE Technical Paper 2009-01-0492 2009
- Arrègle, J. Tormos, B. López, J.J. García, A. “Analysis of the Potential of Biodiesel as an Alternative Fuel for Current and Future HSDI Engines,” SAE Technical Paper 2009-01-0480 2009
- Li, H. Lea-Langton, A. Andrews, G.E. Thompson, M. et al. “Comparison of Exhaust Emissions and Particulate Size Distribution for Diesel, Biodiesel and Cooking Oil from a Heavy Duty DI Diesel Engine,” SAE Technical Paper 2008-01-0076 2008
- Mayer, A. Czerwinski, J. Wyser, M. Mattrel, P. et al. “Impact of RME/Diesel Blends on Particle Formation, Particle Filtration and PAH Emissions,” SAE Technical Paper 2005-01-1728 2005
- Acharya, K. Dahodwala, M. Bryzik, W. Henein, N. et al. “Effect of Different Biodiesel Blends on Autoignition, Combustion, Performance and Engine-Out Emissions in a Single Cylinder HSDI Diesel Engine,” SAE Technical Paper 2009-01-0489 2009
- Aoyagi, Y. Shimada, K. Osada, H. Noda, A. et al. “Diesel Emissions Improvement by RME in a High Boost and EGR Single Cylinder Engine,” SAE Technical Paper 2008-01-1376 2008
- Horn, U. “The influence of Fuel Properites on CI Combustion” Lund University Lund 2008
- Nanjundaswamy, H. Tatur, M. Tomazic, D. Koerfer, T. et al. “Fuel Property Effects on Emissions and Performance of a Light-Duty Diesel Engine,” SAE Technical Paper 2009-01-0488 2009
- Tunestål, P. “Self- tuning gross heat release computation for internal combustion engines” Control Engineering Practice 2008 10.1016/j. conengprac. 2008.09.012 2008
- Heywood, J. B. “Internal Combustion Engine Fundamentals” McGraw-Hill Inc. 1998