This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Residual Stress Prediction in Machined Workpiece Surfaces
Technical Paper
2000-01-1751
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The increasing drive for productivity improvements and consistent part dimensionality in aerospace structures has lead to the advent of machined monolithic parts. High speed machining technology employed affords the manufacture of thin-walled parts from single billets of material, resulting in the removal of approximately 85% of the initial workpiece material. With thin-walled monolithic parts come the increased propensity for workpiece distortion and few arresting mechanisms for crack propagation, largely due to potentially unfavorable residual stress states. These imposed states of stress can be a result of the machining conditions used (e.g., feeds, speeds and cutter geometry). A general method is presented to model the residual stress state induced by metal cutting operations which takes into account workpiece thermo-mechanical properties, cutter geometry and process parameters. In this paper the model is specifically applied to Al7050. Results indicate the magnitude and sign of the state of stress is shown to have no intuitive correlation to machining process parameters such as speed and chip load. Similar results are shown for stress-induced bending moments, a potential strong contributor to part distortion. In addition, the machining-affected layer is shown to be on the order of 1mm, easily on the same length scale as the wall thickness of aerospace structures.
Recommended Content
| Aerospace Material Specification | Core, Honeycomb Fibrous, Aramid Base, Phenolic Coated |
| Aerospace Standard | Center Hole, Metric |
| Aerospace Material Specification | Bearings, Sintered Metal Powder 89Cu – 10Sn Oil Impregnated |
Authors
Citation
Marusich, T., "Residual Stress Prediction in Machined Workpiece Surfaces," SAE Technical Paper 2000-01-1751, 2000, https://doi.org/10.4271/2000-01-1751.Also In
References
- Childs, T. H. C. Material Property Needs in Modelling Metal Machining, CIRP Workshop on Modeling Metal Cutting , 1998
- Flom, D. G. High-Speed Machining,” in: Bruggeman and Weiss (eds.)
- Innovations in Materials Processing, Plenum Press, 1983 417 439
- Kobayashi, S. Herzog, R. P. Eggleston, D. M. Thomsen, E. G. A Critical Comparsion of Metal-Cutting Theories with New Experimental Data Trans. ASME J. Eng. Ind. ( 1960 333 347
- Marusich, T. D. Ortiz, M. Modeling and Simulation of High-Speed Machining
- Int. J. Num. Meth. Eng v;38 1995 3675 94
- Marusich, T. D. Effects of Friction and Cutting Speed on Cutting Force Submitted to ASME
- Journal of Manufacturing Science and Engineering 2000
- Sandstrom, D. R. Hodowany, J. N. Modeling the Physics of Metal Cutting in High-Speed Machining, Machining Science and Technology 2 1998 343 353
- Stevenson, R. Stephenson, D. A. The Mechanical Behavior of Zinc During Machining, Journal of Engineering Materials and Technology 177 1995 172 178
- Strenkowski, J. S. Athavale, S. M. A Partially Constrained Eulerian Orthogonal Cutting Model for Chip Control Tools, Journal of Manufacturing Science, 119 1997 681 688
- Third Wave Systems, Inc. 2000 AdvantEdge v3. 3 Machining Simulation Software Minneapolis, MN
- Obikawa, T. Usui, E. Computational Machining of Titanium Alloy-Finite Element Modeling and a Few Results, Journal of Manufacturing Science and Engineering 118 1996
- Obikawa, T. Sasahara, H. Shirakashi, T. Usui, E. Application of Computational Machining Method to Discontinuous Chip Formation, Journal of Manufacturing Science and Engineering 119 1997 667 674