This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Utilization of a Quasi-Dimensional Model for Predicting Pollutant Emissions in SI Engines
Technical Paper
1999-01-0223
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
In this paper, models developed to determine exhaust emissions from Spark Ignition engines are shown. Concretely, a model based on chemical kinetics for determining CO and NOX emissions is presented. Also it is shown a model for the determination of the HC exhaust emissions based on retention in crevices, wall quenching, and in-cylinder and exhaust pipe post-flame combustion processes. Both models are included in a quasi-dimensional multizone model that permits the fast analysis and prediction of combustion in homogeneous-charge SI engines. Finally, results obtained from the models are compared with experimental exhaust emissions measured in a test bench.
Authors
Citation
Tinaut, F., Melgar, A., and Horrillo, A., "Utilization of a Quasi-Dimensional Model for Predicting Pollutant Emissions in SI Engines," SAE Technical Paper 1999-01-0223, 1999, https://doi.org/10.4271/1999-01-0223.Also In
References
- Cheng W.K. Hamrin D. Heywood J.B. Hochgreb S. Min K. Norris M. “An Overview of Hydrocarbon Emissions Mechanims in Spark-Ignition Engines” SAE 932708 1993
- Namazian M. Heywood H.B. “Flow in the Piston-Cylinder-Ring Crevices of an SI Engine and its Effect on HC Emissions, Efficiency and Power” SAE 820088 1982
- Wentworth J.T. “The Piston Crevice Volume Effect on Exhaust Hydrocarbon Emissions” Combustion Science and Technology 4 97 100 1971
- Boam D.J. Finlay I.C. Biddulph T.W. Ma T.A. Lee R. Richardson S.H. Bloomfield J. Green J.A. Wallace S. Woods W.A. Brown P. “The sources of unburnt hydrocarbon emissions from spark ignition engines during cold starts and warm-up” IMech 208 1 11 1994
- Yoshida M. “An Effect of the Top-land Form of the Piston on Hydrocarbon Emissions of a Spark-Ignition Engine” MTZ 41 93 95 163 171 1980
- Alkidas A.C. Drews R.J. Miller W.F. “Effects of Piston Crevice Geometry on the Steady-State Engine-Out Hydrocarbons Emissions of a SI Engine” SAE 952537 1995
- Min K. Cheng W.K. “Oxidation of the Piston Crevice Hydrocarbon During the Expansion Process in a Spark Ignition Engine” Combust. Sci. and Tech. 106 307 326 1995
- Gatellier B. Trapy J. Herrier D. Quelin J.M. Galliot F. “Hydrocarbon Emissions of SI Engines as Influenced by Fuel Absorption-Desorption in Oil Films” SAE 920095 1992
- Guillemot P. Gatellier B. Rouveirolles P. “The Influence of Coolant Temperature on Unburned Hydrocarbon Emissions from Spark Ignition Engine” SAE 941962 1994
- Kaiser E.W. Siegl W.O. Russ S.G. “Fuel Composition Effects on Hydrocarbon Emissions from a Spark-Ignited Engine. Is Fuel Absorption in Oil Significant?” SAE 952542 1995
- Russ S.G. Kaiser E.W. Siegl W.O. Podsiadlik D.H. Barret K.M. “Compression Ratio and Coolant Temperature Effects on HC Emissions from a Spark-Ignition Engine” SAE 950163 1995
- Adamczyk A.A. Lavoie G.A. “Laminar Head-On Flame Quenching - A Theoretical Study” SAE 780969 1978
- LoRusso J.A. Kaiser E.W. Lavoie G.A. “Quench Layer Contribution to Exhaust Hydrocarbons from a Spark-Ignited Engine” Combust. Sci. and Tech. 25 121 125 1981
- Meernik P.R. Alkidas A.C. “Impact of Exhaust Valve Leakage on Engine-Out Hydrocarbons” SAE 932752 1993
- Alkidas A.C. “The Effects of Fuel Preparation on Hydrocarbon Emissions of a SI Engine Operating Under Steady-State Conditions” SAE 941959 1994
- Fox J. W. Min K-D Cheng W.K. Heywood J.B. “Mixture Preparation in a SI Engine with Port Fuel Injection During Starting and Warm-Up” SAE 922170 1992
- Takeda K. Yaegashi T. Sekiguchi K. Saito K. Imatake N. “Mixture Preparation and HC Emissions of a 4-Valve Engine with Port Fuel Injection During Cold Starting and Warm-up” SAE 950074 1995
- Bownman C.T. “Control of Combustion-Generated Nitrogen Oxide Emissions: Technology Driven by Regulations” Twenty-Fourth Symposium (International) on Combustion The Combustion Institute Pittsburgh 859 878 1992
- Heywood J.B. “Internal Combustion Engine Fundamentals” McGraw-Hill 1988
- Turns S.R. “An introduction to Combustion” McGraw-Hill 1996
- Horrillo A.J. “Modelo de dos zonas para el diagnóstico de la combustion en MEP” IEF internal report 1994
- Tinaut F.V. Melgar A. Horrillo A.J. “Planteamientos cuasi-dimensionales para la predicción de la combustión en MEP” 3 rd Iberoamerican Mechanical Engineering Congress Cuba 1997
- Tinaut F.V. Melgar A. Horrillo A.J. Giménez B. “Uti-lización Conjunta de Modelos Predictivos y de Diagnóstico para la Optimización de la Combustión en un MEP” 2 nd Iberoamerican Mechanical Engineering Congress Belo Horizonte Brazil 1995
- Tinaut F.V. Melgar A. Horrillo A.J. Giménez B. “Análisis comparativo de cámaras de combustión en motores de encendido provocado mediante un modelo de combustión predictivo” 12 th Spanish Mechanical Engineering Congress 195 202 Bilbao 1997
- Horrillo A.J. “Metodología basada en modelos sencillos in ensayos para la mejora de la combustión” IEF internal report 1998
- Dent J. C. Lakshminarayanan P. A. “A Model for Absorption and Desorption of Fuel Vapour by Cylinder Lubricating Oil Film and its Contribution to HC Emissions” SAE 830652 1983
- Linna J.R. Hochgreb S. “Analytical Scaling Model for Hydrocarbon Emissions From Fuel Absorption in Oil Layers in Spark Ignition Engines” Combust. Sci. and Tech. 109 205 226 1995
- Schramm J. Sorenson S. C. “A Model for Hydrocarbon Emissions from SI Engines” SAE 902169 1990
- Hellström T. Chomiak J. “Oxidation of Hydrocarbons Released from Piston Crevices of SI Engines” SAE 952539 1995
- Lavoie G. A. “Correlations of Combustion Data for SI Engine Calculations: Laminar Flame Speed, Quench Distance and Global Reaction Rates” SAE 780229 1978
- Thompson N.D. Wallace J.S. “Effect of Engine Operating Variables and Piston and Ring Parameters on Crevice Hydrocarbon Emissions” SAE 940480 1994
- Carreras R. Comas A. Calvo A. 1990
- Way R.J.B. “Methods for the Determination of Composition and Thermodynamic Properties of Combustion Products for Internal Combustion Engine Calculations” Proc. Inst. Mech. Engrs. 190 60 76 687 697 1977