This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Evaluation of Instability Phenomena in a Common Rail Injection System for High Speed Diesel Engines
Technical Paper
1999-01-0192
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
An existing simulation code of a COMMON RAIL Diesel fuel injector, named UNIJET, has been revised and completed, with the aim to predict injection characteristics and to investigate on the instabilities which appeared in experimental tests. Particular attention has been given to the injector control valve modeling, to understand the influence of cavitation on discharge flow characteristics. The valve residual motion, after a Pilot Injection cycle, is responsible for the clear and sudden injected quantity variations of subsequent Master injection, as the time delay between the two cycles decreases. Numerical predictions have been compared with valve lift measurements, and with experimental relation among fuel injected quantity, injection pressure and duration.
Recommended Content
Authors
Topic
Citation
Ficarella, ., Laforgia, D., and Landriscina, V., "Evaluation of Instability Phenomena in a Common Rail Injection System for High Speed Diesel Engines," SAE Technical Paper 1999-01-0192, 1999, https://doi.org/10.4271/1999-01-0192.Also In
References
- Zellbeck H. Schmidt G. “Einspritzsysteme für zukünftige Anforderungen an schnellaufenden Dieselmotor” MTZ 56 1995 11
- Di Gesù P. Laforgia D. “Diesel Electro-Injector: a Numerical Simulation Code” Transactions of the ASME. Journal of Engineering for Gas Turbines and Power 1995 117 792 798
- Amoia, V. Ficarella A. Laforgia D. De Matthaeis S. Genco C. “A Theoretical Code to Simulate the Behaviour of an Electro-Injector for Diesel Engines and Parametric Analisys” SAE Paper 970349
- Lange C. “Fluiddynamische Optimierung des Steuerventils eines Electroinjektors für Dieselmotoren mit Direkteinspritzung” Diplomarbeit I Gesamthochschule Kasse Universität
- Garro A. Piano L. Viazzi M. “Simulazione degli apparati di iniezione combustibile nei motori Diesel” Congresso ATI Trieste 11 13 1985
- Ficarella A Intini N Laforgia D. “Cavitation Problems of Diesel Engine Injection Systems” International Conference of Mechanics of Two-Phase Flows Taipei 12 15 june 1989
- Chen Y. Heister S. “Modeling Cavitating Flows in Diesel Injectors” Atomization and Spray 6 709 726 1926
- Schmitt T. “Unitersuchungen zur stationären Strömung durch Drosselquerschnitte in Kraftstoffeinspritzsystemen von Dieselmotoren” Heft 58 Forschungsvereinigung E.V. Frankfurt/Main 1966
- Bergwerk W. “Flow Pattern in Diesel Nozzle Spray Holes” Proceedings of Institution of Mechanical Enigneers 173 25 1959
- Ficarella A Laforgia D. “Fluid-Dynamische Erscheinungen in Einspritz-Anlagen” MTZ 52 1 Januar 1991 28 34
- Ficarella A Laforgia D. “Injection Characteristics Simulation and Analysis in Diesel Engines” International Journal of Meccanica 28 1993 239 248
- Pischinger R. Staska G. Gao Z. “Berechnung des Einspritzverlaufes von Dieselanlagen bei Kavitation” MTZ 44 1983 11
- Guido A. Della Pietra L. “Fenomeni d'urto negli iniettori per motori Diesel” Atti dell'Istituto di Meccanica Applicata alle Maccine della Facoltà di Ingegneria dell'Università di Napoli 1980
- Guido A. Della Pietra L. “Fenomeni d'urto e post-aperture nei sistemi di iniezione per motori Diesel” Atti dell'Istituto di Meccanica Applicata alle Maccine della Facoltà di Ingegneria dell'Università di Napoli 1980
- Dow R.B. Fink C.E. “Computation of some Physical Properties of Lubricatin Oils at high pressures” Journal of Applied Physics 11 May 1940
- Nguyen D.L. Winter E.R.F. Greiner M. “Sonic Velocity in Two-Phase System” International Journal of Multiphase Flow 7 1981
- Cardo A. Ceschia M. “A Experimental Study on Cavitation in Unsteady Oil Flow” Bull. Of JSME 22 170 Aug. 1979