Your Destination for Mobility Engineering Resources

To regulate low-altitude UAV operations, this paper proposes a method for constructing a low-altitude layered route network. First, a visibility-graph-based obstacle environment modeling method is adopted to transform geometric constraints in complex low-altitude space into a graph representation, and candidate flyable networks are generated at different altitude layers. On this basis, a set of primary paths and low-overlap alternative paths is generated for multiple origin-destination pairs. To address the redundancy and discreteness of the resulting path set, multiple OD paths are combined into an initial low-altitude airspace route network through path screening, spatial aggregation, and shared-structure extraction. Furthermore, a minimum spanning tree is used to extract the network backbone for topological simplification. On this basis, redundant connections and reinforced critical route segments are introduced through network augmentation and optimization strategies, thereby constructing a low-altitude airspace network that integrates topological connectivity, structural compactness, operational efficiency, and redundancy robustness. Using Longhua District of Shenzhen as the case study area, this paper carries out simulation experiments on airspace planning. The results indicate that the proposed method requires only a marginal expansion of network size, yet it can markedly lower the average detour level of key OD pairs, enhance the two-path reachability ratio, and preserve stronger OD service capability under both random and directional disturbances. Therefore, the method is able to support the efficient construction of layered route networks in low-altitude environments characterized by dense obstacles, while also providing a methodological basis for the operational management of low-altitude UAV systems.
Liu, Mingyu, Zhang, Ying, Yin, Jianan, Tian, Wen, Meng, Fanyu
To enhance the robustness of satellite power systems and ensure overall spacecraft energy safety, this paper proposes a design scheme for a distributed high-power power supply control subsystem incorporating a Sequential Switching Shunt Maximum Power Regulator and a grid-connected controller. This configuration enables emergency power supply and peak power support under fault conditions, thereby improving solar energy utilization and load power reliability. To achieve intelligent grid connection among units, the battery voltage must be converted to a high voltage level with software-adjustable output voltage. For the hardware design of the grid-connected controller, a dual interleaved parallel Buck/Boost circuit plus a DC transformer is adopted as the topology of the bidirectional DC/DC converter, and the state-space averaging method is used to establish the small-signal model of the Buck/Boost circuit. A composite current sharing control strategy based on an analog and digital combined control with the main error amplifier and the droop current sharing method is proposed, which enables bidirectional power regulation through mode selection, avoiding output current polarization risks caused by differences in compartmentalization among power subsystems that lead to inconsistent output characteristics of individual grid-connected controllers. Meanwhile, in Boost mode, an improved algorithm is proposed to address the stability issues caused by conventional droop control. The droop coefficient is adjusted by compensating the bus voltage deviation, ensuring the system operates normally under heavy-load conditions. The composite control algorithm is simulated in MATLAB. Simulation results show that the proposed strategy enables flexible boost-type grid connection among subsystems and effectively improves the power supply reliability of the system.
Xu, Yiyuan, Xiong, You, Cao, Chengrong, Wang, Yongkang, Wu, Ziyue
To address the issue of weak constraints in the transverse and normal directions during space-based orbit determination for cislunar spacecraft, this paper proposes a space-based differenced measurement method. In this method, two Low Earth Orbit (LEO) satellites receive the same measurement signal beam transmitted by the cislunar spacecraft. By precisely measuring the time difference of signal arrival, angular constraints on the cislunar spacecraft are formed, thereby improving the convergence speed and accuracy in the transverse and normal directions of the orbit. The LEO satellites achieve high-precision baselines and relative clock offsets via common-view Global Navigation Satellite System (GNSS) signals. This method requires accurate calibration of the system delay between the two LEO satellites when receiving signals from the cislunar spacecraft. The differenced system delay is calibrated on-orbit using ground stations, achieving an accuracy of 593.7 ps. Taking cislunar spacecraft in both a Distant Retrograde Orbit (DRO) and a DRO direct transfer orbit as examples, this paper analyzes the impact of different LEO baseline lengths (500 km, 5000 km, and 10,000 km) and measurement modes (single-satellite, dual-satellite non-differenced, space-based differenced, and space-ground differenced) on orbit determination performance. Results from a dynamic batch least squares estimator show that for spacecraft in both the DRO and the DRO direct transfer orbit, single-satellite measurements fail to achieve rapid convergence of position estimation within 30 minutes. Under a 500 km baseline, the position estimation for the DRO using space-based differenced measurement converges to 200.3 m within 30 minutes, outperforming the dual-satellite non-differenced measurement (478.3 m). Under the same baseline condition, the position estimation for the DRO direct transfer orbit using dual-satellite non-differenced measurement converges to 2836.0 m, while the space-based differenced measurement achieves a significantly improved accuracy of 1013.0 m. Under a 5000 km baseline, the position estimation for the DRO using space-based differenced measurement converges to 30.1 m, outperforming the dual-satellite non-differenced measurement (84.6 m). Under the same baseline condition, the position estimation for the DRO direct transfer orbit using dual-satellite non-differenced measurement converges to 438.8 m, while the space-based differenced measurement achieves a significantly improved accuracy of 126.3 m. The space-ground differenced measurement fails to achieve convergence for position estimation of the DRO direct transfer orbit but converges to 208.5 m for the DRO. The space-based differenced measurement method can significantly improve the orbit determination convergence speed for cislunar spacecraft in either the DRO or the DRO direct transfer orbit. However, if the measurement arc exceeds one hour, the accuracy advantage of space-based differenced measurement is not significant.
Lai, Weifeng, Wang, Wenbin, Mao, Xinyuan, Feng, Xuan
To investigate differences in driving behavior across different sections of urban underground interchanges and to comprehensively evaluate their safety, this study selected six existing urban underground interchanges in China as case studies and constructed driving simulation scenarios to compare driving behaviors in merging, diverging, and basic sections. From longitudinal and lateral dimensions, four indicators—speed, acceleration, steering wheel angle, and lateral displacement—were selected, and the sample entropy method was applied to quantify safety differences in driving behavior among different sections. On this basis, an overall safety evaluation model based on an entropy-weighted improved grey near-optimal comprehensive evaluation method was proposed, and safety levels were classified using the Rank Sum Ratio (RSR) method. The results indicate that driving behavior safety entropy in merging and diverging sections is significantly higher than that in basic sections, implying lower overall safety. Moreover, longitudinal driving behavior safety entropy is slightly higher in merging sections than in diverging sections, whereas lateral driving behavior safety entropy is slightly lower. The proposed comprehensive safety evaluation model effectively reflects the overall safety levels of urban underground interchanges, with relatively balanced safety grade distributions across different evaluation dimensions. Among the evaluated cases, the Jiaozhou Bay Tunnel Interchange in Qingdao exhibits the highest overall safety level, whereas the Wanshishan–Zhonggushan Tunnel Interchange in Xiamen shows the lowest safety level and is classified as relatively dangerous, indicating the need for enhanced safety measures during the operation and management stage.
Tang, Xie, Yang, Yiqun, Lin, Guojin, Gao, Yanyang, Zheng, Liwen
Regarding the issue in the 2024 version of C-NCAP’s automatic emergency braking (AEB) test where the scene score rates are highly concentrated at the maximum score, and traditional continuous regression modeling is difficult to effectively depict system risks, this paper transforms the AEB performance assessment problem into a rare failure risk prediction problem, and constructs an AEB failure risk assessment method based on LightGBM and SHAP. Based on 464 test samples, an explanatory variable system is established around operating condition parameters, vehicle configuration parameters, and process temporal sequence parameters, and samples with scene score rates lower than 1 are defined as failure samples. Firstly, the original data undergoes outlier removal, missing value handling, categorical variable encoding, and continuous variable standardization; secondly, a robust LightGBM classification model is constructed to predict AEB deduction/ failure risk; finally, the SHAP method is used to conduct interpretability analysis of the model to identify the key factors affecting AEB system performance. The results show that the established robust model achieves good recognition effects on the test set, with an AUC of 0.871, PR-AUC of 0.527, and F1 of 0.667. The feature importance and SHAP analysis results show that the number of sensors, relative speed, alarm-time TTC, braking-time TTC, overlap rate, and maximum braking deceleration are the key variables affecting AEB failure risk. Among them, higher sensor redundancy and earlier alarm and braking trigger times can significantly reduce system failure risk, while high relative speed, complex collision geometric relationship, and braking intervention lag will significantly increase the failure probability. The proposed method can effectively identify AEB system performance risks under the condition of highly concentrated score rates and rare failure samples, providing a data-driven analysis tool for AEB calibration optimization, sensor configuration design, and active safety performance improvement.
Yuan, Yue, Li, Yanchen, Zhang, Changlu, Li, Zhengwei
Due to topographical constraints and limited space for evasive manoeuvres, accidents in mountain expressway tunnels can easily trigger long-distance congestion, queues spilling onto the open road, and even a chain reaction of serious secondary accidents; To address this challenge, this paper explores a low-cost, easily implementable active control scheme. Focusing on single-direction, dual-lane mountain expressway tunnel sections, it proposes a coordinated active control strategy comprising ‘graded traffic restriction at the entrance + in-tunnel speed guidance based on the PSO algorithm’. Utilising the SUMO micro-simulation platform, a control group with no intervention was established for comparison against experimental groups with traffic restriction levels of 30%, 50%, 70% flow restriction levels for comparative validation. Additionally, the PSO algorithm was employed to determine the optimal speed limit combinations during the accident period. Following a multi-objective trade-off analysis of safety indicators and system delays, the study demonstrates that a 50% flow restriction threshold combined with specific segmented speed limits (46.5 km/h upstream of the incident and 19.8 km/h in the core incident zone) constitutes the multi-objective weighted optimal solution that balances both tunnel safety and overall road network efficiency; This strategy successfully validated the ‘congestion displacement’ mechanism, reducing high-risk queuing within the confined space from 600 m under uncontrolled conditions to 128 m. Furthermore, as this low-cost solution requires no complex equipment, it provides a useful theoretical basis and reference for the formulation of emergency management plans for mountain expressway tunnels.
Li, Youhe, Wu, Gang, Huang, Chongjian
Aiming at the problems of insufficient personalized adaptation and partial technologies relying on high-cost sensors in current new energy commercial vehicle energy-saving technologies, this paper conducts research on an intelligent recognition method of driver behavior for energy-saving driving of new energy commercial vehicles. The purpose is to realize low-cost energy-saving assisted driving of new energy vehicles by developing driving behavior recognition. Firstly, vehicle driving data covering various driving states from drivers with different driving styles are collected, and core characteristic parameters of driving behavior are extracted. Then, a driver’s driving style recognition model integrating feature extraction, PCA dimensionality reduction, preliminary clustering classification and LSTM-SVM is proposed to effectively recognize three types of driving styles: aggressive, steady and conservative. Based on this, a closed-loop energy-saving technical scheme of “recognition-adaptation-guidance” is proposed, and differentiated energy-saving optimization strategies are designed for different driving styles. Joint simulation verification shows that the application of this energy-saving scheme can save about 9.1% of energy consumption. The research technology in this paper can carry out driver behavior recognition without relying on high-cost sensors, and is suitable for low-cost new energy logistics vehicles.
Zhang, Hao, Wu, Yutong, Yu, Hanzhengnan, Li, Jingyuan, Wang, Fengbin, Liu, Yu
Tourist bus driver distraction and fatigue are critical driving risk factors, yet empirical studies are scarce due to data limitations. Based on approximately 7 million kilometers of DMS alert data from 692 tourist coaches, this study takes sub-trips as the analysis unit, develops a Gaussian Process Boosting (GPBoost) model with vehicle-enterprise grouped random effects to predict distraction/fatigue risks, and uses SHapley Additive exPlanations (SHAP) to interpret nonlinear variable effects. Results reveal predictive associations of continuous driving time and speed on both risks, interactive associations between speed and driving duration-risk relationships, and context-dependent direction-reversing effects of enterprise management factors across risk types. Vehicle-enterprise heterogeneities in grouped random effects are pronounced, calling for tiered risk management. This study provides a quantitative basis for proactive safety management of tourist buses.
Wu, Yaqi, Liu, Xiaobing
Forming connected and automated vehicle (CAV) platoons before a signalized intersection can substantially increase green-window throughput, yet existing platoon-formation methods target freeways and ignore signal-phase deadlines, while intersection-oriented studies optimise trajectories without addressing the cross-lane gathering process. This study develops a CPS-based, two-layer cooperative control framework to facilitate CAV platooning in the near-signal zones of mixed traffic. At the upper layer, the Signal-Aware Formation Planner (SAFP) evaluates the potential throughput gain of platooning during a given green-light window. It initiates formation only if the expected throughput improvement exceeds a specific threshold. Furthermore, a closed-loop feedback link with the trajectory layer allows the SAFP to adjust plans in real time if a lane change fails. The lower layer jointly optimises the longitudinal accelerations of all platoon-candidate CAVs through a single quadratic program (QP) that explicitly couples inter-vehicle spacing errors—structurally distinguishing it from per-vehicle MPC—while a signal-deadline-aware adaptive weighting strategy modulates the formation-urgency versus traffic-efficiency trade-off in real time. This study evaluated the proposed method using SUMO simulations across various CAV penetration rates (20%–80%) and traffic demands (600–1800 veh/h). Compared to a no-control baseline, our approach reduces average travel delays by 12%–23% and increases throughput by up to 12.9% under congested conditions. Additionally, it achieves platoon formation success rates of 14%–42%, while effectively maintaining safety and cutting fuel consumption by up to 6.1%.
Zhao, Guopeng
Against the backdrop of rapid urbanization, conventional bus networks with fully fixed stations often experience spatial mismatches between station locations and residents’ evolving travel demands, thereby reducing their service effectiveness. Demand Responsive Transit (DRT) can alleviate this mismatch by organizing services through a fixed and flexible stations scheme, in which some stations are retained as fixed anchors, whereas others can be served dynamically on demand. This study investigated fixed station selection for DRT using the existing station set of a conventional route as a candidate pool. We developed an evaluation framework that jointly considers time-dependent passenger flow characteristics and attractions induced by surrounding land use functions. Based on the traditional station impact index, we proposed an improved impact-index model by introducing a land use category weight coefficient to explicitly differentiate land uses with heterogeneous trip-generation potential. The resulting index integrates station-level ridership indicators, such as boardings, alightings and potential served passengers within a given time window, with land-use weights, enabling station ranking, grading, and threshold-based classification for fixed station retention. A case study of Harbin Bus Route 235 was conducted. Using weekday peak-hour smart card data, we estimated the station service demand and obtained passenger flow inputs for the proposed index. Land use information around each station was identified using Point of Interest (POI) queries and mapped to the corresponding weights. By computing and sorting the improved impact index and additionally checking the spatial distribution and inter-station spacing to preserve coverage and leave room for dynamic stations, a set of priority fixed stations for the peak period was determined. The results demonstrate the feasibility and effectiveness of the proposed method, providing an operable reference for scientific fixed-station planning and decision-making in DRT.
Feng, Yuxuan, Zhang, Xiqiao, Lin, Jiadong, Li, Yetong, Lu, Di
To address the load fluctuation problem in distribution networks caused by fixed electricity pricing incentives during EV charging, this paper proposes a novel EV charging power prediction method based on the optimal division of peak-valley time-of-use tariff periods. A charging power forecasting model is constructed with the minimization of the grid load peak-valley difference rate as the core optimization objective. A genetic algorithm is employed to calculate the optimal charging power prediction, yielding the forecasting results corresponding to the optimal peak-valley tariff period division scheme. Numerical simulation results demonstrate that the proposed method not only effectively enhances the prediction accuracy of EV charging power but also significantly mitigates clustered EV charging behavior and substantially reduces the peak-valley difference rate of the total grid load.
Liu, Zhongkai
This article focuses on the intelligent upgrade of the online monitoring system and builds a three-level intelligent network architecture of “vehicle terminal-edge node-cloud platform” to achieve efficient collection, transmission and processing of multi-source heterogeneous data. The vehicle-mounted terminal completes real-time collection and preprocessing of data from core components such as batteries, motors, and electronic controls; edge nodes rely on edge computing technology to implement local data analysis and task offloading, reducing transmission delays; and the cloud platform builds a global data processing and decision-making system to support fault prediction and status assessment. Design multi-source heterogeneous data fusion algorithms, fault prediction models and real-time status assessment methods based on deep learning to break through the bottlenecks of low data utilization and lag in fault prediction in traditional monitoring systems. An optimization strategy is proposed from three dimensions: communication delay, data transmission efficiency, and system energy consumption, and system overhead is reduced through 5G-V2X communication optimization, lightweight data transmission protocols, dynamic task offloading and other technologies. Build a simulation and physical experiment platform to verify the effectiveness of the proposed architecture and method. Experimental results show that the end-to-end transmission delay of the constructed system is reduced to less than 35ms, the data transmission efficiency is increased by 42%, the system energy consumption is reduced by 30%, and the fault prediction accuracy reaches 96.2%, which meets the real-time, accuracy and reliability requirements of online monitoring of new energy vehicles.
Wang, Zheng, Liu, Liya, Ran, Longyi, Yao, Sankun
Modern air defense missiles often adopt additional boost stages to achieve extended range and increased velocity, which must be separated from the main missile body once the boost stage is finished. To investigate the aerodynamic field characteristics and motion behavior during the stage separation process, numerical simulations were conducted using an unstructured overset grid method. Simulations were performed for various angles of attack, combined with six-degree-of-freedom equations of motion to analyze the post-separation dynamics of the missile body. The results demonstrate that, despite the main stage maintaining an axisymmetric geometry, inter-stage disturbances caused by asymmetric attitude changes in the boost stage induce yaw and roll attitude variations post-separation. Furthermore, the roll angular velocity of the boost stage increases with the angle of attack at the moment of separation. Notably, the maximum relative displacement between stages occurs under negative angle-of-attack flight conditions, which is most favorable for successful stage separation due to minimized aerodynamic interference.
Zhang, Zilun, Qiu, Zhongyu, Mei, Zhiwei
High-altitude wind interference poses severe threats to the attitude maintenance and safe landing of reusable launch vehicles adopting vertical landing mode. Such adverse impacts become particularly prominent during the aerodynamic deceleration stage, where the main engine is shut down and the available control torque is strictly constrained. Conventional wind forecasting approaches fail to deliver timely real-time results and often require additional sensor configuration; meanwhile, classic control methods tend to suffer from obvious chattering phenomena and slow convergence speed when exposed to strong external wind perturbations. Targeting the above practical limitations, this study develops a finite-time adaptive attitude control strategy integrated with online wind estimation, which is tailored for vertical landing launch vehicles under sparse sensor measurement conditions. This work first constructs an attitude dynamic model oriented to controller design. The model fully takes into account the coupling effect between attitude angles and angular velocities, as well as the nonlinear characteristics introduced by wind disturbance. On this basis, an LSTM network is established to implement real-time wind estimation and prediction. The network only relies on easily measurable state information including pitch, yaw and roll angles, together with normal and lateral apparent acceleration deviations, eliminating the need for specialized wind measurement sensors. With 8-bit quantization and 30% parameter pruning optimization, the lightweight network is compressed to 89.6k parameters. Deployed on a radiation-hardened PowerPC 750FX processor with 1 GHz main frequency and 256 MB memory, its single inference latency is only 7.2 ms, which fully satisfies the time limit of onboard control loops. Furthermore, relying on homogeneity principle, this paper designs a non-recursive high-order sliding mode control algorithm with homogeneous characteristics. It can guarantee finite-time convergence of attitude errors and effectively restrain system chattering. An adaptive compensation module is also embedded to offset wind perturbation by utilizing the estimated wind information output from the LSTM model. Simulation comparisons under six typical wind environment cases verify the effectiveness of the proposed method. The results demonstrate that the designed scheme can cut wind disturbance torque by a maximum of 55.3% and reduce the demand for control torque by 52.7%. It also shortens the attitude stabilization duration by 35% and lowers the range of attitude angle fluctuation by 69%, which effectively improves the system’s anti-interference capability and environmental adaptability to complex wind conditions.
Fan, Chenxiao, Yao, Yuemin, Chu, Lin, Gu, Hailun
Rapid advances in aerospace technology urgently demand the construction of ultra-large space structures (ULSSs) as primary components for spaceborne antennas, solar arrays and space telescopes. On-orbit assembly overcomes the constraints of rocket thrust and fairing envelope, serving as a new deployment paradigm that replaces traditional single-launch deployable structures. To address the degradation of surface precision caused by cumulative manufacturing and assembly errors in modular assembly, as well as thermal deformation during on-orbit service, this paper proposes a surface prediction and control method for ULSSs based on a sensitivity matrix and an iterative quadratic programming solution. First, the configuration and structure of the assembled antenna are designed, and a surface precision optimization model is established. Second, a sensitivity matrix is constructed using first-order Taylor expansion to predict surface precision. Subsequently, the optimization model is transformed into a quadratic programming form, and an adaptive learning rate is designed to enable fast iterative solution. Finally, surface precision control simulations are conducted for two typical operating conditions (ground assembly and on-orbit service) using a 100-meter single-wing antenna composed of 25 modules. When all struts are adjustable, near-zero RMS surface precision is achieved; with ±2 mm actuators arranged on diagonal struts at one-module intervals, an RMS accuracy of 2 mm is realized. The proposed method provides strong support for the high-precision on-orbit deployment of next-generation spacecraft
Yin, Ke, Wu, Chunbing, Jia, Mingyue, Cui, Qifeng, Xie, Chao, Qiu, Houtong
In order to obtain an aircraft with excellent control characteristics, in its design indicators, maneuverability and agility have become important assessment contents. How to obtain the aerodynamic and moment coefficients of the aircraft with high credibility is extremely important for more accurately describing the aircraft’s characteristics in the high angle of attack region. Based on flight test data and considering the influence of engine thrust vector, a typical six-component force model is constructed to identify the aircraft’s steady-state high angle of attack and post-stall maneuvering actions, obtain the aerodynamic forces and moment coefficients, and compare and verify them with the ground wind tunnel prediction results. Analyze the deviation patterns between the two and clarify the correlation between the wind tunnel test results and the flight test identification results. Form a method for identifying and analyzing the aerodynamic forces in the high angle of attack region of the aircraft based on flight tests.
Shi, Jiawei, Liu, Miaoxin
There is a significant difference between the atmospheric temperature measured by tropospheric flight parameters and the atmospheric temperature calculated by the international standard atmospheric model. Based on the international standard atmospheric model, this article selects flight parameter measurement data within the tropospheric height range under typical seasonal and airport conditions to modify the atmospheric temperature model. The modified atmospheric temperature model is closer to the actual atmospheric temperature. Applying this modified model to aircraft flight performance calculation can obtain more accurate calculation results. The results show that using the modified atmospheric temperature model to calculate the range performance of aircraft can improve the results by more than 5%. This research result can be applied to tasks such as aircraft engineering development and daily test flights.
Zheng, Fengmin, Bai, Junqiang, Niu, Ben
In densely urban mixed transportation networks, the dynamic features of the internet of vehicles (IoV) frequently alters connectivity, challenging the safety of connected and autonomous vehicles (CAVs) behavior planning, especially in ramp diverging areas where mixed traffic flows and diverse driving intentions converge. To address this, this paper first construct a multi-view graph neural network (GNN) model that captures spatiotemporal dependencies among CAVs and human-driven vehicles, incorporating speed, intention, and lane-changing behaviors. This multi-perspective model enables a comprehensive understanding of heterogeneous interactions. Building on this, this paper introduce a driving behavior safety prediction mechanism based on artificial potential field (APF) theory to quantitatively evaluate risks between CAVs and surrounding IoV elements, including other vehicles, road boundaries, and destinations. These two components form a collaborative safety behavior planning framework tailored for ramp scenarios, implemented within a graph reinforcement learning framework with a reward function that balances efficiency, safety, and ride comfort. The framework demonstrates strong adaptability to varying traffic densities and driver behaviors. Experimental results on a realistic urban traffic simulation platform demonstrate that compared to benchmarks (A2C, DQN, PPO), the proposed algorithm improves average speed by at least 0.1%, reduces average steps by at least 0.3%, and increases normalized cumulative return by at least 0.5%, while achieving a zero collision rate. These results validate the effectiveness of the proposed framework in enhancing both efficiency and safety in densely urban mixed transportation networks, effectively alleviating congestion and contributing to smoother traffic flow at critical ramp sections, thereby offering a promising solution for future autonomous driving systems.
Sun, Yidan, Yang, Fan, Huang, Jie, Yu, Chengbo, Ding, Ruijie
Under severe illumination shifts, the detection representation space is disrupted, ultimately manifesting as weakened object boundaries, foreground-background activation imbalance, and abnormal response diffusion during multi-scale feature fusion. To address this issue, we propose a targeted enhancement framework for YOLO26 under illumination-hard conditions. The framework preserves the original backbone-neck-head architecture and performs conditional enhancement only on key intermediate features during the forward pass of the DetectionModel. Specifically, a 5-dimensional global illumination condition vector is extracted from the deep SPPF feature via ICE-Z; three independent FiLMHeads then predict dedicated modulation parameters for the three critical nodes, namely the high-level semantic node A, and the multi-scale pyramid nodes P3 and P4; finally, SAGFiLM performs condition-driven dynamic feature correction with residual reinjection. Compared with the YOLO26x baseline of the same model scale, the final model improves Precision, Recall, mAP50, and mAP50-95 on BDD100K-hard from 65.69%, 49.02%, 57.51%, and 35.66% to 75.18%, 51.00%, 59.33%, and 36.26%, respectively. On VisDrone-hard, the corresponding metrics increase from 90.66%, 85.43%, 91.84%, and 64.42% to 91.38%, 86.35%, 92.65%, and 64.98%, respectively. Meanwhile, the method introduces only about a 0.31% increase in parameters and an additional training overhead of approximately 8.71%-10.36%. We also report its performance degradation on the full-set distribution, indicating that the proposed method is a robustness enhancement mechanism tailored to a specific working regime rather than a universal plug-in applicable across arbitrary distributions.
Li, Zhe, Li, Yan
With the continuous advancement of vehicle safety technologies, the Automatic Emergency Braking (AEBS) system has become a key component in preventing traffic accidents. However, existing research and testing primarily focus on conventional road conditions, while the system’s performance under extreme environments such as snow and ice remains insufficiently investigated. This paper investigates the challenges encountered by AEBS when addressing Vulnerable Road Users (VRU) in low-friction snowy conditions, analyzing the degradation of sensor performance, uncertainties in decision-making, and actuator limitations arising from reduced friction and low-temperature effects. Furthermore, current regulatory frameworks lack comprehensive test scenarios for icy environments, with existing standards providing only limited assessments under static or simple motion conditions. To address these gaps, this study proposes six representative test scenarios defined by varying snowfall intensity levels, target object types, and vehicle motion states. The evaluation criteria focus on collision avoidance and vehicle stability after braking. The findings contribute to a more systematic and scientifically validated testing methodology for AEBS in winter environments, offering critical insights for future regulatory development and technological advancements in vehicle safety.
Shen, Liangyi, Qi, Yunpeng, Wang, Zhiyu, Xi, Ruixuan, Gao, Zong, Kong, Lingming
To improve the static and dynamic stiffness of CNC lathes under the action of complex cutting forces, ANSYS software was used to conduct static simulation on the headstock, tailstock and saddle of the LH40 CNC lathe, and analyze the influence of deformation and stress distribution on static stiffness. Dynamic simulation was carried out, and MATLAB software was applied for data processing to investigate the effects of natural frequency and easily excited frequency on dynamic stiffness. The results show that the maximum deformation of the headstock is 4 μm with a maximum stress of 3.3 MPa, and the maximum amplitude of the first 6-order natural frequencies is 0.038 mm; the 1st, 2nd and 4th-order natural frequencies are more likely to be excited in the frequency range of 0~1000 Hz. The maximum deformation of the tailstock is 1.5 μm with a maximum stress of 2.1 MPa, and the maximum amplitude of the first 6-order natural frequencies is 0.040 mm; the 2nd and 4th-order natural frequencies are more likely to be excited in the frequency range of 0~1750 Hz. The maximum deformation of the saddle is 0.015 mm with a maximum stress of 12.2 MPa, and the maximum amplitude of the first 6-order natural frequencies is 0.16 mm; the first 4-order natural frequencies are more likely to be excited in the frequency range of 0~1000 Hz. The research results have important theoretical significance and engineering application value for the optimal design of the whole CNC machine tool.
Qin, Lei, Sun, Changyuan, Geng, Jinyu, Sun, Xiaolin, Shi, Baozhou
With the development of China’s automotive industry, a pattern of diversified automotive products has been formed, and the accompanying product competition has become increasingly fierce. In particular, in the field of automated mechanical transmission (AMT) commercial vehicles, vehicle manufacturers no longer take “high load capacity and high operating efficiency” as the sole goal in new model development. Instead, they focus more on the driving quality of products to enhance their competitiveness among similar products. In the process of new vehicle model development, drivability evaluation serves as an important basis for improving vehicle driving quality, enabling developers to accurately identify drivability issues. Although the AVL-Drive objective test system includes evaluation working conditions for vehicle drivability, it is not fully applicable to the test requirements of domestic complete vehicle development. In view of the development of vehicle drivability by vehicle manufacturers, this paper proposes a drivability evaluation test method for AMT commercial vehicles based on the AVL-Drive objective test system, which provides a reliable basis for designers to optimize vehicle performance.
Wu, Wenwen, Fei, Yuanjun, Wang, Changqing, Geng, Hao
Aiming at the wing of a civil aircraft, this paper first conducts the preliminary design of the wing by using the shock control bump (SCB) optimization design platform, and then investigates the influence of SCBs on the static aeroelasticity of the wing with the flexibility method. The results show that SCBs have a negligible effect on the static deformation of the wing, and still exhibit a drag reduction effect on the wing after static deformation. SCBs can alter the shock wave structure and improve the flow state of the wing surface. After installing SCBs on the clean wing, the drag coefficient is reduced by 3.32% and the lift-to-drag ratio is increased by 6.10%.
Gao, Jianfeng, Dai, Jiahua
When operating at low altitude, UAVs are exposed to gusts, unsteady aerodynamic loads, and electromagnetic (EM) interference at the same time. A fixed-geometry airframe has no recourse against this kind of compound threat. In this paper, a four-stage methodology called Disturbance–Response–Mapping–Optimization (DRMO) is put forward. It follows the propagation path of external disturbances — from macro scale down to micro scale — until the disturbances surface as measurable performance loss. Three groups of variables enter the formulation: morphing configuration (span reduction ratio r, camber adjustment), skin topology (ZPR honeycomb, auxetic, corrugated), and functional compensation. Calculations are carried out on a 2.0 m span, 5 kg platform. Helmbold lift-slope theory combined with a simplified flutter model shows that r = 0.15–0.20 cuts gust load by 17–23 % and keeps the flutter speed ratio above 0.95. Skin strain-to-frequency drift is captured by a power law (k = 1.8, n = 1.6) whose coefficients originate from published silicone-substrate antenna data. A ±15 % perturbation of these coefficients does not move the design-window edges outside the acceptable band. The intersection of the three constraint boundaries fixes a passive window at r = 0.15–0.20. Adding piezoelectric LQR stiffness control widens it to r = 0.25 without degrading flutter safety.
Wang, Lechen, Zhou, Tingyao, Qu, Fangqi, Zheng, Jiaou, Chu, Lingling, Jia, Yilin, Yan, Jingjing